(800) 853-2651
SHOP NOW

Recent content by 450 Farmall Hooker

Yesterday's Tractor Forums
  1. 4

    m with 301

    To see 2400 on the engine, you need to turn the pto shaft on the m at about 890 rpm. Use the 1000 scale and a slide rule on an M&W dyno to figure your hp. I bet you like the new number better.
  2. 4

    conformatic piston

    Anyone know the size of the dome on a conformatic 4.125" piston for a farmall? Also, the cc's added with a victor gasket?
  3. 4

    strategy

    If you find yourself lucky enough to be the first puller in a class, and you know that you can re-do your pull if you want, what strategy do you use for your first pull? Do you look for something on the track? Do you run full or part throttle? Do you bugger it up on purpose to mess with other...
  4. 4

    M transmission

    Can you swap the entire top and bottom shafts, or all the gears from a farmall m to a super m? Does a m and a super m have the same differential ratio?
  5. 4

    Fiberglass fuel tank

    Can he mount a spun aluminum tank inside the fiberglass tank?
  6. 4

    light weight farmall m front end

    What is the weight compared to factory, what hubs do you put on, and what do you figure the cost would be? Thanks
  7. 4

    re-torquing a head gasket

    On a 450 farmall, how many times should you re-torque the head? Is there any reason or benefit to do it more than once? How hot should you get things before a re-torque?
  8. 4

    Farmall 4.25 bore

    Thanks.
  9. 4

    Farmall 4.25 bore

    When you pull the liners out of a super M/400 block, the block bore is 4.25" correct? Can you run 4.25" pistons in this bore simply by honeing the block? Who would make filler rings and pistons for a setup like this?
  10. 4

    Farmall head gasket

    The old (few years ago) Super M/450 gaskets were metal both sides. The new ones, to my suprise, with the same part number, are only metal one side. Any place to get an old style metal both sides head gasket? Manufacturer and part number? Just a stock bore.
  11. 4

    M block clearancing

    Do you clearence the cylinders before or after boring and honeing? If after, do you do any chamfer/radius to the edge of the clearenced section? Do you run the hone through again after finished? Does the piston skirt run at the clearenced section of the cylinder?
  12. 4

    Farmall 9 bolt hubs

    I have read that Massey 44, and Oliver 88 hubs will both fit, but are bad for breaking. Will either of them work with a custom machined key and no grinding of the hub? Does anybody make aftermarket clamp on hubs? 2 3/4 axle. Farmall tapered key.
  13. 4

    Farmall 9 bolt hubs

    Those are 3".
  14. 4

    Farmall 9 bolt hubs

    What kind of 9 bolt hubs will fit a 450 farmall and take the abuse of pulling up to 8000lb? Is M&W the only type or is there something else? I am looking to buy. Tell me what you have.
  15. 4

    306 engine

    What do I have to do to get a solid 75hp at 540 pto out of a 450 gas with a 306 overbore? Any info as far as compression, cam, and carb would be great.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top