(800) 853-2651
SHOP NOW

Recent content by 6cylpower

Yesterday's Tractor Forums
  1. 6

    acrylic pourable product

    Smooth-On EpoxAcast 690 is what I have used but not cheap. Careful your entering a deep rabbit hole!
  2. 6

    EV Battery fast chargeing

    But it's likely more than the car is worth now. Autotrader has several listed in the $10-20K price range. Would make me nervous to have a $15k budget for a car knowing it could need a $19k battery if they still make it when mine dies. https://www.autotrader.com/cars-for-sale/chevrolet/volt
  3. 6

    Question About Horsepower

    The OP asked about plowing. I will stick with my 3720 for the above tasks..
  4. 6

    Question About Horsepower

    I have a dyno sheet that came in Deere service bulletins when the model 60 came out. 43 hp and 250 ft-lb. My 3720 utility has 44 engine (35 pto)hp and 84 ft-lb. (doesn't say engine or pto) Which will pull a plow better?
  5. 6

    Unusual wheel weight part number

    Picture in the book is for spinouts, takes a different weight than regular cast as the parts list shows. I think that is just a generic pic anyway. This post was edited by 6cylpower on 03/06/2023 at 02:16 pm.
  6. 6

    Unusual wheel weight part number

    26" & 28" cast wheels, R32015 weight
  7. 6

    Sigourney pull

    Is the antique class meaning the '38 and older like they used to have?
  8. 6

    Movable gantry while loaded?

    The local you-pull car parts yard made some gantries that use 15" car tires. I used one to pull a 4 cylinder engine out of a car and squeeze down the isle of cars to my pickup. Worked well, ground wasn't that level either. Just googled these. Notice no trolleys so the load stays centered...
  9. 6

    john deere cam grind advice

    No keys on a B cam, it bolts to the gear. Slot the holes if you want some advance.
  10. 6

    problem tools; PayPal and eBay

    Is your browser up to date? I have an older operating system that is no longer updated. I forget the site now but I could add items to the cart and go through the whole checkout stage. After I put in my card info and clicked ok it would decline it. I had to use another browser that is still...
  11. 6

    John Deere 40 engine block

    jdfun320 wrote: (quoted from post at 06:20:02 01/11/23) We have several M64T blocks available. We are located in S.E. Mo. Thanks , Tom Ziegler 573-535-8952 I found Tom very reputable Me too
  12. 6

    1949 B Oil Filter Body

    No clips. Either your shaft is stripped or the cast is stripped cracked. Picks are from a -46 B, threads into center of left piece
  13. 6

    Wd45 or Oliver 70

    The original poster should probably be the one to decide what class he wants to pull in, and get better advise if he shared that here. How about a 77?
  14. 6

    What is it?

    Thanks Jim. I've seen the air bearing fixtures for grinding flutes but never would have thought of this. My little stub of a tape measure keeps the new tape from breaking so soon! Measuring inside corners are hard on them, plus its easier to read than a regular steel rule.
  15. 6

    What is it?

    Got this on an auction with some other stuff. The outside center holes are adjustable with a little scale. And one end is adjustable.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top