-
A
135 rims on TO30?
They're both bolt loop. Thanks for the info!- acaswell
- Post #3
- Forum: Harry Ferguson
-
A
135 rims on TO30?
Hey all, i've got a to-30 with 12.4x28 on 11" rims and one of them is rusted out and needs replaced. I was searching for replacements and came across a pair of 12.4x28 on 11" rims in good condition with weights that came off a massey ferguson 135 for the same price I could get one new tire...- acaswell
- Thread
- Replies: 2
- Forum: Harry Ferguson
-
A
Flail Mower
I have that same mower and it runs fine on my 3000 (71 3cyl diesel). I do have a loader on the tractor so that might help balance the weight. -
A
C9NN1A002E rear weight mounting
They came off an old 800. They match the curve of the rim and the center hole is big enough that the lug nuts are easily accessible assuming the weight's centered on the rim. -
A
C9NN1A002E rear weight mounting
I recently was given some C9NN1A002E wheel weights for my 74 Ford 3000. They didn't come with mounting hardware and when I got them home, I realized I have no holes in the wheel centers for them. Those weights are supposedly supposed to fit my tractor so am I missing something? Is it as... -
A
64 Ford 2000 tractor gear vs hydraulic fluid
I have a 3000 that developed a pretty bad transmission leak last spring(would leave a solid line of oil down the driveway in 3rd). I was using it almost daily so I didn't really have the time to split it and repair the leak so I tried adding some AT205 to it. It took a few weeks to work in but... -
A
Trying to find out if this is part of the 3 point hitch
It's a guide rod for the draft control system. I figured that out after I snapped one off replacing the seat on my 3000. I ran for a while without it using position control only for the 3 pt and never had any issues, but I'm not sure how wise that decision was. -
A
Hydraulic Lift Is Dropping and Hiccuping
They’re in the hydraulic section of the service manual. -
A
Hydraulic Lift Is Dropping and Hiccuping
My 74 3000 would act very similar with a 6' finish mower. I got the hydraulics off and didn't find any worn or missing parts, but I did discover that it was adjusted per the specs for the earlier version (pre-69). I adjusted it to the correct specs and also pulled a bunch of wood out of the... -
A
3000 Power Steering System Cost
I purchased a 74 3000 a few years back with aftermarket steering and after breaking the mount for the second time, I decided to put OEM steering on it. It took me about a year to round up all the parts I needed from salvage yards and the internet. I had to rebuild one of the cylinders and the... -
A
Ford 2000 tractor seat bolt/stud problem
what happens if this pin isn't there? I recently took my hydraulics apart for cleaning and adjustment and that back seat mount was just a bolt. I thought it was a little odd that the hole went all the way through. I've only had the tractor a few years and don't use it very much so I'm... -
A
Ford 3000 weak power steering
Never thought to question the cylinders! I pulled the lines for both cylinders this morning and plugged the ports in the control valve. Still no pressure change when I turn the wheel and I did confirm that oil is flowing back into the reservoir with all four cylinder ports plugged. I'm... -
A
Ford 3000 weak power steering
So I dead headed the pump and started the tractor and the pressure shot up over 600 at which point, I shut the tractor off to avoid pump damage. As I mentioned before, there's no pressure change when I turn the wheels to the stops either way, so I'm back to something being amiss in the control... -
A
Ford 3000 weak power steering
The tractor came a few years ago with aftermarket steering and I decided to put a loader on it which the steering wouldn't support. I was able to source most of the parts I needed from a local junk yard to convert to OEM power assist steering. I re-used the pump and reservoir from the...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy