-
A
4000 seat adjustment
I have a 70 Ford 4000 S/U same seat trouble.I would like to see a parts page to see what is in there.Before I tear into the adj. Till then it will be a rough ride. Hope you get some help.Then I might too. THANKS Al -
A
Leaking pitman shaft seals on power steering
good I was hoping that would work thanks Dean -
A
Leaking pitman shaft seals on power steering
1970 4000SU can the seals be replaced without taking the pitman shaft out of housing? Thankyou for time and help.Al -
A
no down pressure on 3pt . blade
thanks for your answers.Have agood evening.Al -
A
no down pressure on 3pt . blade
1970 Ford 4000SU 3cyl.gas, never realized till Sunday I have no down pressure on 3pt. hitch lifts ok holds ok I have a bush hog front loader on it,is it possible it has been plumbed to bypass 3pt. hitch? What about the flow control valve would that affect it? I don't want to get into the cover... -
A
Would my 1970 4000 SU work good with 3pt. tiller?
I would like to get a tiller wide enough to cover wheel tracks,if my budget will allow it .Thanks again. Al -
A
Would my 1970 4000 SU work good with 3pt. tiller?
I have a 1970 4000SU 3 cyl. gas I call it an 8 speed(4with hi&lo). Would this old girl be good with a tiller? Or would it be to fast? Thanks for the help. -
A
How can I drop the amps on my 12 volt jump box?
The rechargable battery is 12v 9.5amp. I tried with jump box seems ok, wires or motor did not feel hot.That jeep will move right out now. Maybe I can borrow grandmas lawn mower battery when she's not mowing. Thanks again for all your help -
A
How can I drop the amps on my 12 volt jump box?
Thanks I think I'll go try it. Al -
A
How can I drop the amps on my 12 volt jump box?
Is it possible to drop the amps on my 12 volt jump box to 9.5 amps so I can power my grandaughter's toy jeep? The jeep is rough not really worth a new battery. I don't want to burn out the drive motors with excess amps. Thankyou for your help. I know this is not a tractor question but I do have... -
A
1970 4000 3cyl gas 12v gen
4000 is not charging. I checked voltage at batt while running high rpm about 12v, same as not running.I looked at some archives but did not find info I need. Do I need to polarize? If I do , I need to take a wire from batt to terminal on gen. I don't know which term. I dont see any letters or... -
A
FORD 4000 SU
Thanks Mark internet has been down thats why it took so long to get back to you.Al -
A
FORD 4000 SU
Mark Where can I get this kit? It looks like there is a snap ring that comes out. Is the next part threaded or held in by the snap ring? Thanks for the info. Al
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy