(800) 853-2651
SHOP NOW

Recent content by alaska jd

Yesterday's Tractor Forums
  1. A

    tractor shows and pulls

    I will be in southeast texas the last week of april and first week of may. Does anybody know of any tractor shows or pulls about that time? Thanks for the info. Dave in Alaska
  2. A

    tractor shows and pulls

    I will be in southeast texas the last week of april and first week of may. Does anybody know of any tractor shows or pulls about that time? Thanks for the info. Dave in Alaska
  3. A

    fairbanks morse mag

    Thats correct. Thanks
  4. A

    fairbanks morse mag

    1941 B FMJ2B6 Already have a few parts coming but nothing else was broke. all broken pieces came apart once out. didn't destruct while rotating.
  5. A

    fairbanks morse mag

    I have a slight problem with my mag. I tore it all apart for a good cleaning and inspection. The armature (rotating magnetic thing) was completely destroyed. Once out of the housing it just fell apart, magnets, steel plates and broken casting steel everywhere. Now for the hard part. Where can I...
  6. A

    Fairbanks Morse on Styled B

    Hey there guys. I have a Fairbanks Morse J2B6 on my 41 B. Is this the correct mag? It has run with this one and wanted to make sure there is nothing wrong with applying this style before I restore it. Thanks for any and all info again. DM
  7. A

    alum. piston pin tolerance

    Thanks for the feed back you guys. I think I'll give the pistons a slight hone and then try again. Thanks for the info, always helpful.
  8. A

    alum. piston pin tolerance

    The pins are new and the alum. pistons are new also. came in a set. pins are way to tight. if i warm them up wont the tolerance be to tight for oil lubrication? planned on honing the pist a litte. don"t have to worry about getting them apart if i cant get them together in the first place. anyone...
  9. A

    alum. piston pin tolerance

    Hey there again guys. My question is this. Should the piston pin on aftermarket alum pistons (for a 41' B)still be a "thumb push" fit? They a very very tight and plan on honing the piston just a little to make them fit. Any ideas. They are thumb push fit on the original cast pistons just like...
  10. A

    jd b 41

    I am looking very hard to find new pistons for a mid b. ser number 96947. oversized at least .045. I cant find a set anywhere any help would be greatly appreciated. thanks guys. Dave M.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top