(800) 853-2651
SHOP NOW

Recent content by anoelke

Yesterday's Tractor Forums
  1. A

    806 replaced mcv pump and lost brake pressure?

    The posts/video are really helpful. Same with the diagram. Have the seals but not the springs, will get to work on it tomorrow. Thank you
  2. A

    806 replaced mcv pump and lost brake pressure?

  3. A

    806 replaced mcv pump and lost brake pressure?

    I replaced the pump and the gasket on the plate between the pump and the body of the tractor plus the seals on the shaft of the pump and the O-ring that fits into the body of the tractor, but did not see other seals and not sure what the spools are.
  4. A

    806 replaced mcv pump and lost brake pressure?

    Hello everybody Have a 1966 806 that I use for grinding feed and chores daily on the farm. After changing fluid and filter I Replaced mcv pump due to losing steering constantly. Steering is now great but brakes are barely working. Bled but didn’t find much air. Pedal has much less pressure...
  5. A

    806 remote levers hanging up

    Another post explained how to pop round covers off under seat at back.. each valve has a flat head groove to adjust. Tried a turn in and out but it didn’t seem to be affecting it so I left it how I found it.. my guess is this controls flow but not for sure.
  6. A

    806 remote levers hanging up

    Wish I could get video to upload. It’s not that. it is really stiff and snaps in and out only if you really push on it. About halfway into the full stroke up or down on one lever and only on the down side on the other. Does it if tractor is running or not.
  7. A

    806 remote levers hanging up

    appreciate y’all’s help so far as I get used to my 806. Got the shifter and hydraulic issues straightened out.. now that I can use the front and loader I’m having issues with the two levers that control the remotes getting stuck up or down. I can push on him hard and they snapped back into...
  8. A

    806 steering fails

    Been having issue with steering on my 806 diesel. Using loader to unload pallet of minerals and wasn’t able to lift ( about 2400 lb) took a few bags off and could lift but the forks kept uncurling slowly. And then lost steering completely. Wheel turns easily but tires don’t move at all. Next day...
  9. A

    806 questions

    Thanks all for the good advice. Got the tractor home last week but it took a few days to get the loader bracket adapted and just started using yesterday. Runs great, but After using all day had a few things turn up. First, Hydraulic levers that control the remotes work but get stuck. You can...
  10. A

    806 questions

    And what about the other lover that says light on one side and heavy on the other? It was stiff, but since I had no idea what it did I didn’t really wanna mess with it.
  11. A

    806 questions

    Another thing on the Tractor surprise me, but I’m not familiar with old international. The lift arms go up and down well but if you let go of the control lever, the lever drops down immediately. You can move a limiting knob to stop it not sure if this is how it’s supposed to work or if there’s...
  12. A

    806 questions

    The all right, so just had more time to go through this Tractor and there is a pretty good size puddle of hydraulic fluid underneath what looks like a valve maybe for the steering it’s behind the battery if you look from one side or kind of under the starter if you look from the other seller...
  13. A

    806 questions

    Really appreciate all the good information convince me to make the long drive to go. Check it out.Went and saw Tractor yesterday and there’s less smoke than I’ve ever seen on an old tractor. Shifts really well steer is good. Sounds fantastic. Body is straight and paint is good. has good...
  14. A

    806 questions

    Engine wasn’t rebuilt just head machined and valves replaced. Going off what owner says,everything you mention works right. Engine smokes a little . He says due to new valves not being worn in. Is that believable?
  15. A

    806 questions

    Looking for a tractor to use 3-4 times a week to grind feed and 2 times a year to shred 60 acres. Found an 806 that’s been fixed up that looks pretty sharp. New gauges engines been gone through, inject pump has been rebuilt. Shifts well no leaks. Anybody out there still using these daily? Are...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top