(800) 853-2651
SHOP NOW

Recent content by ArloInt

Yesterday's Tractor Forums
  1. A

    12 volt neg ground Altenator output

    Ok Tim. thanks for responding back. Front mount dist. Took the alt to a shop this am, checked good. 70 amp output. 14v. also. reinstalled. checked all connections have only one wire which runs from the post (backside) of alt. I noticed when they checked the alt they pluged a two spade...
  2. A

    12 volt neg ground Altenator output

    I converted to 12v system about four years ago. everything good until today. Now only getting 12.1 volts at the battery. motor running. one wire at alt. get 27v from post and ground. I expected 12.8/13.2 at battery. amp gage not showing any movement. Any thought about this. maybe a diod in...
  3. A

    Front mount dist.

    I just wiped out my Dist, after replacing bushings. The weights iunder the plate are messed up. It looks like to me I either buy new dist. or can I go with electronic ignition. Don't know what parts would be used, if any with elec. ignition.
  4. A

    valve ID.

    Thank you, exactly what I wanted to know. Now I feel comfortable checking and adjusting valves.
  5. A

    valve ID.

    Thanks Jim for your response I am not wanting to remove the hood or the head to make the checks. My manual is not clear on exhaust valve location and I am not certain looking at the manifold. think I will have to study it a little closer.
  6. A

    valve ID.

    Order of exhaust and intake values. correct me if wrong. I'm trying to adjust the valves.. 8n front mount distributor has about 12 hours on it since rebuilt.. looking at the valves, (head is on) two cover plates off. cyl #1 right valve exhaust-left valve intake. cyl number 2, 3, 4 should...
  7. A

    8N spark plug wires

    Is there any difference for front mount dist. and side mount plug wires. Local want $41 for set side mount. Yt $12 and change. But don't know if they will work for front mount dist. Thanks
  8. A

    8N head bolt or studs/nut

    Thanks you for the reply.
  9. A

    8N head bolt or studs/nut

    need information on 8 N head bolts. What grade of bolt will it need. Or would it be better to stay with studs.
  10. A

    info needed 8n head bolt or studs

    Puting my 48 8N together. the shop thinks I should use bolts instead of the studs. 7/16 x 3 inche studs. if I were to go with a bolt what grade would I need to look for and I feel the length would be different. maybe 2 1/2 inches
  11. A

    Oil pump kit

    Sorry 8N "48"
  12. A

    Oil pump kit

    Just about ready to pickup my motor from the shop. The shop ordered a new oil pump kit, know one of the gears just slides off, but not sure what problem I will have removing the other gear. Is it going to be a problem? Thanks for any info.
  13. A

    8N motors

    Thanks for the number. Did a compression test and found #1 @ 80, #2 @ 80, #3 @ 50, and #4 @ 0 , Listening it sound like it is coming from the 3 and 4 piston area. just about ready to put the hoist on and remove the front end.
  14. A

    Parts

    I'm looking for the the compessure gauge tha that I gve my son last fall. want to get an idea on compession, then will start tear down. Thanks for info. Will have to reread your 50 tips again
  15. A

    Parts

    Black Forest, Just west and a tad north of you and thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top