(800) 853-2651
SHOP NOW

Recent content by AWoods

Yesterday's Tractor Forums
  1. A

    Alternator 283 Brazil

    Having a hard time finding a exaxct fit. Has anyone change one of these with the built in regulator they all seem to come that way now. If so it would seem you have to change the wiring to go around the old regulator? I am not talking about the single wire delco I cant fined one of those with 60...
  2. A

    update on 283-275 pulling power

    After changing the spin rims to the 283 witch I think closed the gap on wheight diference. The 283 pulled the the 9" talorway harow good. If anything it pulled it better than the 275. Very happy with my move to 283. My great looking 275 is now up for sale.
  3. A

    410 massey combine

    I have a freind that says some parts are a problem to get for them now. Very hard to get to certain parts to change out.
  4. A

    pulling power 275 vrs 283

    I bought the 283 going to swap the spin out rims to the 283 witch seems to be where a lot of the weight is. At some point I will let everyone know just how equal they are in pulling. Thanks for the replies any others are welcome.
  5. A

    pulling power 275 vrs 283

    Does anyone have any experience on this? The horepower rated the same but the weight seems to be lighter on the newer 283. I have a chance to buy 283 with only 900 hrs on it. I have the 275 pulling a 10 foot heavey harrow pulls it good but seems to be all it wants. I don"t think I can aforde to...
  6. A

    Power Steering on a 275

    I would recomend finding a good after market pump replace it. Ajusted mine it only helped for short time then it began to leek. You can buy rebuild kit but is half the price a new aftermarket and dosn't include a shaft that could be worn. Fluid is hydro trany flid John deer or massey aproved. I...
  7. A

    248 oil pressure in 275

    blow by hole not pluged up. It will use about 1 quart with about 5hrs.hard work dosn't use with light wiork. But I cant figure out why pressure be up if it has the blow by piston. just don't understand what is going on. Thanks for feed back.
  8. A

    248 oil pressure in 275

    What I forgot to say was when hot it will spit oil out dipstick if you pull it out. Is that normal? It dosnt push it out when the stick if firmlly in place.
  9. A

    248 oil pressure in 275

    What should it be when worked hard heat is up? It starts out stays about the same 65-70 psi all the time tryed two gagues. I have chek blow by seenms to be fine. Oil reports show high wear. It was rebuilt has about 1000 hr. The Massey gauge stays in yellow. If that is too high pressure what...
  10. A

    Ford 309 Plates

    I have some e mail me at [email protected] we can see if I have what you need.
  11. A

    Changing oil seal handpump powerstearing

    How dificult of a job on a 275 is this to do? manual tells me how to get hand pump out but dosn"t detail the oil seal and o ring change.I have fluid coming out at the stearing wheel. Is the seal in the top of the pump?
  12. A

    eng. temp.pressure

    275 with 248 eng. When worked hard temp likes stay on high side just below the red but never runs hot. Temp stays on botoom of geen if doing light work. Never builds up any pressure on radaitor cap tried new cap also. never need to add water level stays up. Going to have oil cheked seems to...
  13. G

    What to do with Kohler TH Triad V-twin?

    I bought an 18hp K V-twin and one for parts thinking to build one good engine for my Power King. Found out I have an odd Triad model with OHCams, not just valves. They have timing belt and sleeves that seem to slip out of position I was told. Anyone need parts for one? Simplicity used this...
  14. A

    175 blow-by

    I have this same problem After having rebuild and head work. My question is will this harm my engine if I run it much befor I fix it? It uses no oil just will spit some out the dip stick if you pull it out. Mine is 275 With A-248
  15. A

    David P. could you

    This is A-248 Perkins in 275 it has the motor balancer with the oil pump on back this I replaced along with all was done you covered except the injectors and fule pump. I saw just a baffel plate I think when the hose was removed. I can't remeber will have to check on the rebuild kit as a...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top