(800) 853-2651
SHOP NOW

Recent content by Biz

Yesterday's Tractor Forums
  1. B

    Deere Flangeless Thrust Bearings

    It was my local Deere dealership, I just thought they'd be familiar with such things when I asked about it, repeatedly. The bearing I got was a JD thrust bearing minus the flange/washers. It even has notches to engage the washers, which really had me going hmm. RE27351 In my googling it...
  2. B

    Deere Flangeless Thrust Bearings

    And the link red MN sent for the non-Spain version (I think non-Spain) had bearings that cross reference with the new part numbers I got from JD, so in theory they had the bearings but the washers didn't show up as related. I don't know how it works for them. I do appreciate the assistance...
  3. B

    Deere Flangeless Thrust Bearings

    The existing is definitely a flanged thrust bearing. A Federal-Mogul bearing, as it were. More back story, I pulled one main and one rod bearing and both were .010 over/undersized. Great, order a set, then found the rear main was .020" Ugh. But, that saved me from taking bad parts counter...
  4. B

    Deere Flangeless Thrust Bearings

    I should also mention, this engine has had its bottom end worked over at least once before. After the week or more of looking at these bearings I've started thinking maybe I should replace the existing aftermarket flanged bearing with a similar part. I have the part number and found an...
  5. B

    Deere Flangeless Thrust Bearings

    Thanks for the response and hello. It is from Spain with SN above 50000. That's the parts catalog bookmark I start with when searching. Under that Spanish tractor, the engine shows a diagram with flanged bearing, which of course, has been replaced. The link you sent was for the German made...
  6. B

    Deere Flangeless Thrust Bearings

    I'm in the process of an in-frame rebuild on a JD 1630 with 3-179 engine, my first diesel rebuild. I decided to use JD bearings for mains and rods. When I picked them up, the thrust bearing was the "newer" flangless style. Ok, so I ask the guy at the counter, do I need thrust washers, and...
  7. B

    Little advice needed.

    What did you figure out for the torque spec? You know, for the next guy who's looking...
  8. B

    Torque Spec Differences, main and rod caps

    Hey all, I'm new here so hopefully this is the section for this topic, it's like restoration work. I have lots of things to discuss but the issue I've stumbled onto most recently is torque specs for main and rod caps. I have a JD 1630 with the 3-179D engine. Going to swap some bearings, and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top