(800) 853-2651
SHOP NOW

Recent content by Blaine K

Yesterday's Tractor Forums
  1. B

    FRIENDS SHOP BURNED

    Motrack, nice of you to kick a guy into the ground when he's already in a bad way. Prayers for your friend Zane. And prayers for Motrack as well, I think he has a long taxing road ahead of him as well.
  2. B

    Cold Weather Start (here we go again)

    inline heater.
  3. B

    Cold Weather Start (here we go again)

    I prefer the circulating inline heater. The magnetic oil pan ones are ok, but they only give you isolated heat and can cause hot spots on the pan. I use a coolant circulation heater on my skidsteer.
  4. B

    Thanks everyone for the clutch help !

    Thanks.
  5. B

    Thanks everyone for the clutch help !

    Thanks for the tips. Good advice.
  6. B

    Starter fluid leak? Help!

    Jimps,there are 4 Welch plugs on that side of the block, one of them being right behind the starter. The plugs are the disk type of welch plug, they are 1 3/16" in size. I got my replacements at NAPA. Just drain the coolant system, drill a hole in the centre of the faulty plug and pry out with a...
  7. B

    Starter fluid leak? Help!

    Brass Hammer.
  8. B

    Starter fluid leak? Help!

    Jimps, I am just in the middle of a rebuild on my 9n and I may have had the exact issue that your having. There are 4 Welch plugs on that side of the block, one of them being right behind the starter. The plugs are the disk type of welch plug, they are 1 3/16" in size. I got my replacements at...
  9. B

    fluid typs and volumes

    You will definitely want to change the oil, especially if you live in a cold climate, water being heavier than oil will end up at the bottom after seperation and freeze. And this being where your hydraulic pump resides can do some damage. The power of frozen water is amazing upon expansion. Your...
  10. B

    Thanks everyone for the clutch help !

    Hi all, Thanks for all the input from everybody for my clutch dilema. I have since split the tractor apart again, (its amazing how fast this can be done when you know what's involved the secondtime around). I have the flywheel getting turned at the machine shop, ordered a new pressure plate...
  11. B

    Clutch issues

    Thanks, Dell, I did replace the clutch in the proper orientation. The reason I mentioned it was that one of the earlier posts mentioned pressure plate set-up. There really is not much to these clutches other than alignment with either the input shaft or an alignment tool. I think it must be down...
  12. B

    Clutch issues

    Yeah, I did use the old pressure plate, I just ordered a new one, a new fork, and alignment tool. The pilot and throwout bearings were already repaced. I guess that this is a lesson in trying to pinch a penny at the wrong time. Is there any adjusment on the pressure plate at all or is it just...
  13. B

    Clutch issues

    Thanks for the reply, but like I said this clutch problem existed before I did the rebuild on the engine and replaced seals and clutch plate, as well as throwout bearing. The only thing that I did note when putting everything back together was that the fork that pushes the throwout bearing was...
  14. B

    Clutch issues

    I dont recall any adjustment on the pressure plate fingers ? Don't they just engage, disengage with the clutch throwout bearing force (thrust)?
  15. B

    Clutch issues

    Hey Tom, thanks for the reply. Ya ive tried that but no luck.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top