(800) 853-2651
SHOP NOW

Recent content by Blast52

Yesterday's Tractor Forums
  1. B

    NAA cable snow plow apparatus

    I aquired an easy life Jubilee. The tractor has been a joy to get back to good looks, and to operate as well. The tractor had installed on the front and rear axle a set of brackets(?) that were presented as having been used for a cable type hoist arrangement for a snow plow using the 3 pt...
  2. B

    NAA front axle

    Bought a Jubilee and it has hardware on front axle for what I assume is a snow plow mount. These brackets are attached via the bolts that couple the axle "knees" to the axle. I have tried to drive out the bolts with no success. Is there a trick I need to know? Are the bolts pressed in or a...
  3. B

    Jubilee hydraulic problem

    I just picked up a Jubilee also. What is the proper transmission/hydraulic oil. Can I use 134 or do I need 90 wt. or 8N Mineral oil? Thanks for any help. Blast 52
  4. B

    1968 M670 Super

    Any more detail? Where in PA ? Blast52
  5. B

    Cold Fuel Oil Furnace

    Thanks to all you guys for the help. I feel like an idiot- I searched again for a reset and found it on the blind side of the burner motor- reset it and bingo!it works. (IT is also a lot warmer today) Blast52
  6. B

    Cold Fuel Oil Furnace

    It is -10 here in Cent. PA. My shop has a fuel oil-hot air furnace . Oil tank is outdoors. I went to start the furnace this AM and the burner pump ran slow and ground to a halt. The motor barely hums . No circuit breaker or furnace control trips. Any ideas or is it what iI think- Gelled fuel...
  7. B

    5 Star Drawbar

    Thanks to all for the suggestions etc. I took the drawbar to a spring shop which had a 100 ton press. They worked the drawbar on the press and all is well. The spring pepole said the drawbar was cast steel and would NOT do well with heat. Blast 52
  8. B

    Massey Harris Model 60 3 pt. mower

    I am overhauling this mower and need to source the sickle bar knives. I mistakenly thought that standard NH 3" knives would fit, but the rivet holes are less than 2" centers. The knives are 3" with 3/16 rivet holes on approx. 1 7/8 centers. The unit is manufactured by Detroit Harvester. Any...
  9. B

    tricycle front

    Yes, it has spindles and hubs on the assembly.
  10. B

    tricycle front

    Can't find your e-mail address. E-mail me if you can find my E-mail address. Ha! We sound like computer dullards!.
  11. B

    tricycle front

    I have a tricycle pedestal from a 5 Star. Location Pennsylvania. Make a fair offer.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top