(800) 853-2651
SHOP NOW

Recent content by bmiller36

Yesterday's Tractor Forums
  1. B

    delete

    I was wondering if a TSX 887 64m will work on my 3010 untill I get the usx rebuilt , Will it work why or why not Thanks Bob
  2. B

    JOHN DEERE UNSTYLED B

    Ok Im all out of ideas! How on earth do you put that spring and ball into the pto shift lever . Im all out of ideas. Thanks Bob
  3. B

    BR

    Can I use heat on the main bearing to free it up from the crank {rust} also you heat the bearing not the crank? Thanks Bob
  4. B

    john deere br

    send me an e mail with your adress and your location I will buy it if your close enough
  5. B

    john deere br

    what part of mn are you Im around belle plaine
  6. B

    john deere br

    Im looking for a used hood and radiator top for a br. Also what is the difference between crankshafts from the br to the unstyled b. Thanks
  7. B

    john deere 70

    I have a model 70 with a broken clutch driver. The bolts holes that are for pulling it off are broke. I put a large bearing puller behind the gear and tightened the puller as tight as I could, Hit it with a big hammer and it didn't move. need help thanks Bob
  8. B

    John Deere 2020 Runs great for about half hour

    Sounds like a condenser, They act just like that when their bad.
  9. B

    ar

    What is the going rate to grind the valves and seats on a john deere ar? Got one apart and the seats are alittle pitted. Thanks
  10. B

    3020 Gas Starter

    Ive got a 3010 Gas and I DEPEND ON IT! I have a good 12 volt bat on the frame rail ,not those long ones and it always starts in the cold without plug in. I just crank the steering wheel left and right to center the hyd and away we go.
  11. B

    1949 JD B

    thats the serial tag in the distribtor
  12. B

    49 ar

    yes the pump coupling is broken. I have a good number of two cylinders and have never had this happen! So my next foolish newbie question is how to go about fixing it. I really appreciate your help, Bob
  13. B

    49 ar

    I have a 49 AR that has sat in my shop for about 4 years, was working on the sheet metal. Yesterday I decided to get it started, it hadnt run in probably 6 years but after cleaning the carb and mag it started fine and i drove it out of the shop and into the shed. Thats when I noticed it didnt...
  14. B

    4020

    Thanks alot guys now I understand
  15. B

    4020

    Could someone help me decode my serial no ? Its t213p123284r I cant understand how to read the year .Thanks for you help Bob
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top