(800) 853-2651
SHOP NOW

Recent content by bruce-HT

Yesterday's Tractor Forums
  1. W

    Husquvarna K760 Gas Cutoff Saw Compression

    Hi, How much minimum and maximum compression should this saw have to run and idle and start right ? It is a K760 chop saw or concrete saw . It is app. a 2006 model . Thanks for any and all help . Whizkid Breakdown Of Saw
  2. B

    tamp gauge

    Changed my thermostat and put in new coolant on my 641. After filling with coolant, started the tractor and my temp gauge was dead as a doornail. I had replaced the gauge several weeks ago because it had never worked. Out of desperation, I backed the sensor fitting out of the head until it...
  3. K

    Mounting a loader on a WD-Help

    I've got an AC loader made by Freeman that I took off a WD last year, sold the tractor. Now I want to put on another WD, but with my poor memory, I can't for the life of me remember where the lines connected. There is a remote control valve for it and it has a trip bucket. Think this old age...
  4. J

    farmall md overhaul

    Hey guys been kicking the idea around my md has 9100 hrs on original hr meter think its time for a overhaul what's a ball park cost for a complete overhaul including machineing the head???
  5. M

    Helper springs on F Gleaner header lift

    My F has a bean header with 2-wire floating bar controls. My header has a toggle switch that you flip forward. The head will lower till it floats...will raise if the feeler rods hits the other bar. My Question is why do some combines have helper springs on the lift cylinders. Does it help float...
  6. M

    massey ferguson 35

    My MF35 diesel was going well. Then we discovered air in the fuel making it conk out. We think that is fixed but now although she turns over, she won"t fire up. There is smoke coming out of the chimney. She is a recent buy. Any ideas?
  7. B

    mirror

    i am needing a replacement mirror for my ym 1610d,do you have one that fits on the original bracket thanks, bruce
  8. B

    yanmar 1610d brake pedal sticking

    when the brake pedals are unlocked one is staying down,i can usually pull it up but it is getting more difficult to do.is this an easy fix
  9. A

    801 will not start

    I have a 801 ford with select o speed transmission. I had this problem on this site befor but have more information and need more help. my problem is i cannot get the starter to turn over. first notice the wiring and the key switch was getting hot with key off. when trying to start solenoid...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top