(800) 853-2651
SHOP NOW

Recent content by Bub

Yesterday's Tractor Forums
  1. B

    case 400 super diesel

    never had it under a load just up and down the road and pretty quick
  2. B

    case 400 super diesel

    where do you get them worked on or get parts
  3. B

    case 400 super diesel

    i will try dont know how long it set before i bought it
  4. B

    case 400 super diesel

    when i get my 400 started it will run as long as you want just wide open i drove it four half an hour as soon as i backed off it dies so it has to be running on fuel
  5. B

    case 400 super diesel

    my tractor has an american bosch psb injection pump dont know if problem is here
  6. B

    case 400 super diesel

    will start with either but only run wide open new filters need help
  7. B

    48 cub float setting

    what is the float height supposed to be on a 48 cub. im either flooding or starving cant get it right. thanks in advance.
  8. B

    Fordson Super Dexta Purchase

    My dad bought one brand new in 1963, . It is still a great workhorse.These tractors seem to be able to handle any job.the perkins 3 cyl is a great engine.this is the first tractor I ever drove as a kid. 39 years later it is still working on the farm.Power is unbelievable for a tractor of this...
  9. B

    MORE 44 B QUESTIONS

    THANKS FOR ALL THE ENCOURAGING WORDS GUYS I WAS WANDERING IF I GET IT UP TO TEMP IF I SWAPPED OVER TO KEROSENE IF I WOULD GET MORE POWER, OR WOULD I BE ABLE TO TELL ANY DIFFERENCE? I HAVE RUN IT ON KEROSENE BEFORE JUST DRIVING WITH THE SHUTTERS CLOSED AND IT RAN VERY GOOD. NOW WHEN I MEAN THIS...
  10. B

    1944 b

    thanks for the encouraging words guys, i cant wait to get more corn to grind.would i get more power if i got it up to temp and switch to kerosene? or would i not be able to tell any difference. i have run it on kerosene before just driving it around with the shutters closed,and it runs real good...
  11. B

    1944 b

    i have a 44b all fuel tractor that iam using to grind feed pulling a #88 stover hammer mill, that is in inside our mill. we pull the tractor in the engine room and hook the belt on it and it turns a line shaft that the hammer mill is hooked to on the floor above. we ground 1200 lbs. of corn in...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top