(800) 853-2651
SHOP NOW

Recent content by Bud Kaiser

Yesterday's Tractor Forums
  1. B

    Farmall 806 3 point lift problems.

    Are parts readily available to rebuild a Farmall 806 diesel rear lift cylinder ? I have been waiting for over a month and now the tractor repair shop says they don't want to repair my 806 diesel 3 point lift due to parts are unavailable thru IH (he doesn't want to use aftermarket kits due to...
  2. B

    Farmall 806 diesel

    I am going to replace my water pump on my 806 diesel tractor. I see it has a o ring but no gasket. For those of yall that replaced your water pump , did you put any sealant where its bolted to the housing? Also the I am replacing the thermostat . I see a gasket and 2 seals for it. I would think...
  3. B

    Farmall 806 front end.

    How do you tell if the wide front end on a 806 is a IH or Schwartz.? I need to replace a wore out tie rod end. Thanks:
  4. B

    Ford 4600

    Thanks Bern . Yes I can screw stud in about 2 inches. I think I will try it. Just wanted other opinions.
  5. B

    Ford 4600

    I broke 1 bolt off on my loader support bracket that bolts to tractor ( upper bolt). I removed the bolt but noticed the housing on the one next to it had a hairline crack but threads still good. I was thinking on putting studs in place of the bolts. Do yall think this will hold?
  6. B

    1086

    Thanks for all yall's replies. But heck dad still can jump flat footed out of the back of a pick up truck bed . I hope I can do this when I am close his age. I know deere are nicer but always wanted a 86 or 66 series tractor. Never been around any just want some tips on buying a decent...
  7. B

    Update on 560 clutch problem

    Thanks for all yall's responses. I took the linkage off and seen for myself that the T/A does not seem to effect the clutch operation. I then adjusted everything back to spec and clutch and T/A work fine. It is working ok now ( do not understand why sometimes ok then a few days later grinds when...
  8. B

    560 Diesel

    I have 2 batteries around 800 cca each in my 560 diesel, the same size I put in my dodge cummins trucks and they are 5 years old and it still starts just fine
  9. B

    560 T/A

    Trying to figure out problem with hard to get tractor in gear(grinding). Clutch does not slip but does let out at the top of petal travel and T/A shifts and works fine. The only way it will go into gear is I have to adjust the T/A to where it rides against the T/A clutch fingers. Does this...
  10. B

    560 2 point lift cylinder.

    Can this cylinder be rebuilt . I see there is a lever that goes from the cylinder to the teledepth. Does this control internally on the cylinder and how does it work ? My cylinder works fine but leaks out around shaft seal.
  11. B

    Ford 4600 Leak

    I think I got everything back in place but I will check. It has been leak free and have put about 50 hrs on it before it started seeping again. I guess will have to live with but it seems to me to be a poor design. I just thought maybe yall had same experience .I guess while shredding brush it...
  12. B

    Ford 4600 Leak

    I replaced hydraulic oil and filters along with both brake rod rubber boots( from New Holland dealer) about 6 months ago and now the right side is leaking again. Is this something that always leaks ? Any suggestions on how to fix this to last.
  13. B

    Farmall 560 Clutch problem

    Thanks for yall's input. I still do not understand how a locking brake (I watched and it does not move the clutch petal) causes the clutch not to work properly.I guess something internal must move when brake grabs just do not know what. I will address the brake problem but until this happens...
  14. B

    Farmall 560 Clutch problem

    I have a strange problem that happens to my clutch. My RT brake will lock when cold if not slowly applied but works fine after using it and when this happens I cannot shift tractor into gear (grinds like clutch not working) Last 2 times I adjusted T/A but this time adjusted and put back too...
  15. B

    2940

    I just changed out my coolant with a 50/50 mixture of antifreeze and distilled water. Do I need an additive to protect my liners? If I do what do yall use or recommend? Thanks:
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top