(800) 853-2651
SHOP NOW

Recent content by Cal MI

Yesterday's Tractor Forums
  1. C

    D Flywheel spacer drive pin D 2009R?

    My D parts book shows a pin D2009 that drives the flywheel spacer (I call it a main brg. oil slinger). When I took my D apart I did not find the pin. There is a notch in the slinger but no hole in the flywheel for a pin. The spline is deeper on one side that is supposed to slip over the set...
  2. C

    Removing cast wheels from D axle

    Thanks for the help. These wheels are splined on the axle only. There is no wedge and bolt system. And the tractor is torn down completely so I will not be able to drive it around. Not at least until I get it back together and running. Can i put a hydraulic jack between the gear case and the...
  3. C

    Removing cast wheels from D axle

    How does one go about removing the cast wheels from the axles on a '47 D. I tried with a puller and got no where. Am I going to have to remove the whole axle to get it in a press or what? Thanks for your help.
  4. C

    Valve identification

    Thanks for the information Cal
  5. C

    Valve identification

    I have a pair of small engine valves that I need help in identifying. They are new in the JD box with a number T12873T. A search has not helped me identify the application. Can you help?
  6. C

    D Pistons, Aluminum LP for Gas?

    My son is rebuilding a '37 D. He has acquired a set of Johnson aluminum pistons # D1981. These were an after market piston to convert to LP. Will these work on a regular gas run engine? What will be the compression ratio? Is the Compression ratio different than the new pistons available today...
  7. C

    Main Bearings

    I need some help. I have two sets of main bearings that I am trying to identify. I don"t have a JD box for them so I don"t have the JD part number. The bearing halves do have a number stamped on them. It is (FM C 1750 R). That number doesn"t show up on any John Deere number search. If you can...
  8. C

    JD 40 corn head

    I tried to remove a stalk roll today. I could not get the roll pin to come out. I tried punch and hammer and an air hammer to no avail. What is the trick? Do I need to torch it out?
  9. C

    John Deere wheel weights

    What is the part number for wheel weights for my 1948 D. I bought a set of weights last week D2628R. When I got home I found out they do not fit my cast wheels. I have not found the part number in the D parts list. Does anyone have a picture of what the right ones look like? Thanks.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top