(800) 853-2651
SHOP NOW

Recent content by carpman15

Yesterday's Tractor Forums
  1. C

    hydraulic cylinder double to single

    to me one of the big advantages of going back to the resivior is that the cylinders shouldn't rust as easy as if you just put one of those breathers in there- but like was said if you have double acting cylinders why not use them -unless there is something to do with the control's that you cant
  2. C

    Farmall M rocker arm question

    im about 98% sure the only thing they changed was the head i know the block was the same im fairly sure the rocker arms and everything else is the same i have a diff. head on my m than what was on it and the rocker arms still work fine
  3. C

    To Bob/wis

    i have not been there i may have to look into that one of these days - gonna be a little harder getting to salvage yards now that im on third shift but some how i will find time for tractor stuff
  4. C

    Farmall M Seals

    ih is kinda hi on seals for this i priced em out because i need the same ones and a few more for those 2 seals and any gaskets needed to replace them and the pto gaskets and seals i think it was like 100$ maybe there just always high on seals and that but the place i go is usually pretty good...
  5. C

    H belt pulley engagement rod

    if you want if you were to tell me what one you needed i could get you one next time i go up to the salvage yard
  6. C

    To Bob/wis

    hows his prices?? can you go out and dig around and look for what you want?
  7. C

    VAC-14 Discing Video

    nick you look a little light in the front end there when you turn around how was your haul when you came up here by me and jim? i will be going to shawnee oklahoma this weekend to check out the southern tractors and deliver some parts down there
  8. C

    VA? Question

    it woulndt be all that hard to bolt a rockshaft on and you would have an eagle hitch/ 3pt and the hydraulics woulndt take much either u should be able to pop the plug out and put the pump in and plumb it up it may take some time and a little money but if you can find one in a scrap yard you...
  9. C

    farmall m serial number

    im probbaly wrong but i thought the x1 at end ment it had the low low gear
  10. C

    Removing transmission cover...

    i did mine with 2 people wasnt that heavy just kinda bulky i think it would be easier with two people than with a hoist just my opinion on it ive never tried to use a hoist when you put it together make sure the shifter forks are in the correct spot
  11. C

    970 AerWaying

    you have any problems with the teeth in there ? guy i worked for had one and he replaced all the teeth with ones from a company called gen-till they were cast iron instead of forged and the guy at gen-till was convinced they were far better in rocks - i would spend 2 hours at least every day...
  12. C

    Cast Iron pistons in an M

    my 41 m has cast aluminum flat top pistons and i got the rings from here for like 50$
  13. C

    Rusty Farmall

    the last ones o put in on my m i tried to get one from ih dealer and they gave me hard rubber/plastic ones i made my own out of old radiator hose from work (work on semis) had a piece of 3 in radiator hose and cut squares out of it - you could make them round if u want and then used a...
  14. C

    Can I use a used piston on 400?

    you should be ok doing that as long as the bore is the same etc wrist pin diameter also i would think it would be just fine
  15. C

    Barn Fire

    it can be done the 9130 i was driving at the farm started on fire while i was driving it, it was hot enough to melt aluminum fuel pump and filter base etc and lots of wires - needless to say it is running again - the fd did spray the block with water and it wasnt cracked so who knows. the fire...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top