(800) 853-2651
SHOP NOW

Recent content by Charles Grindstaff

Yesterday's Tractor Forums
  1. A

    Correct torque

    I'm replacing the gasket on the inspection cover (right side with dipstick) on my 8N. Does anybody know what I should torque the bolts down to?
  2. C

    600 ford stalling

    Thanks guy's,I will put the old condensor back in and see what happens!
  3. C

    600 ford stalling

    I didn't have spark
  4. C

    600 ford stalling

    Sorry for lack of info, it seems to be getting plenty of fuel,It doesnt sputter like its running out of fuel its like you turn the key off when it dies. I replaced the points,condensor, cap and button about 2 weeks ago. A couple of time I sanded the points and it started back up but just ran for...
  5. C

    600 ford points

    Can anyone give me a quick how-to for installing points on a ford 600 gas engine.
  6. C

    TO-35 steering colum

    Thanks
  7. C

    TO-35 steering colum

    Looking for a steering colum for a 1955 MF TO-35 manual steering.
  8. C

    to-35 manual steering shaft

    looking for a good used or new steering shaft for a MF TO-35 (manual steering)
  9. C

    mf135 for parts (burnt)

    Im looking for a complete steering box for a TO-35, call me at 423-741-5001
  10. C

    TO-35 Steering Shaft

    I"m looking for a steering shaft for a MF To-35,new or used in good shape. Thanks
  11. C

    Oil leak and smoking

    TO-35 has oil coming out of the spark plug holes,fouling plugs and smokes whitish smoke all the time. I checked the compression and this is what I got 85-90-85-90, i"m thinking valve seals are bad but I am open to suggestions before I start tearing it down.It"s a z134 4cyl gas engine. Thanks
  12. C

    no clutch after TO-35split

    bent disk when I put it back together,there"s another 110.00 down the drain.
  13. C

    expansion plug

    Thanks for your help!
  14. C

    expansion plug

    Found a pin hole in the middle of my expansion plug at the back of my Z134 cont. engine,could this be where my oil is leaking? And how hard are these to change and where can I get one? Thanks for the help
  15. C

    still leaking oil

    Gear oil has a distictive smell,this looks and smells like engine oil, plus no oil showing on dipstick and I had just filled it up,surface of block and crank looked good.Hole is open because fluid is coming out.Thanks for reply
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top