(800) 853-2651
SHOP NOW

Recent content by Charles Moore

Yesterday's Tractor Forums
  1. C

    Looking for Deere

    I have a JD 320 S for sale with out belly mower one can be added. Michigan
  2. C

    Throttle lever

    This may be a stupid question but I have JD 320 with should be the same as a JD M I need to no witch way is the throttle lever at idle. With the lever up or down. I am trying to adjust the govenor linkage. Thanks
  3. C

    Remove rear

    I have a JD 320 S , I need to know how to remove the rear nut and Web wheel to replace the seal no.7406 T, because I have oil leaking down the inside of the R. wheel and tire. Thank You
  4. C

    Kubota hyd capacity

    Yes It Would
  5. C

    Help

    M and 320 are the same Thanks
  6. C

    Help

    I just bought a J D 320 S 1956, and it will not idle down, I have had the carb rebuilt and it does the same thing. It runs at fast idle. The idle screw is about 1/8 inch from the stop when running. If I increse the RPM with throttle lever it will stall, why would it stall when I increase the...
  7. C

    Draw Bar

    How far should the draw bar stick out past the end of the PTO shaft on a JD 320 S-330 S. Thanks Charles
  8. C

    Draw bar

    I have a 1956 J D 320 and does anybody know how long a stock draw bar with the curve should be.Thank You
  9. C

    Emglo 335TV Compressor Rebuild

    On the compressor it is 14" pully and on 5 HP motor it is a about 6 " Both are double pullys. If you need a motor I have a 5 HP that is barly used . Will run CW or CCW. $200.00 cost new over 500.00. [email protected]
  10. C

    Emglo 335TV Compressor Rebuild

    If you are looking for a replacement compressor, I have one that is not used much and I will be selling soon for health reasons. It is a Kellogg 335 TV with pully 2stage 14" pully $150.00 plus shipping from Michigan [email protected] Also a 5 hp Dayton motor with pully. hardly used.230 volt...
  11. C

    Emglo 335TV Compressor Rebuild

    I have a used Kellogg compressor with pully and It would mount up to your tank with no problem Had for years and it has very little use in my garage. Model 335 TV Let me no. $150.00 plus shipping
  12. C

    Engine Bearings

    What bearings are in the JD 320 S for main bearings, Babitts or insert bearings, I think the rod bearings are insert bearings. Thank You
  13. C

    Trans

    I have 1956 J D 320 and it has a sloppy tansmision shift lever, and has anybody had this problem before, Need to know how to repair it, What usely wears ot. [email protected]
  14. C

    Carb

    Looking for some feed back on with carb shop I should have overhaul my carb. I is between Robert carburator Repair in Iowa or Dennys carb repair in ohio. Any body have expreince with either. Thanks Charles
  15. C

    Shift tower

    I have a John Deere 320 with a very sloppy shift lever, What could be the problem, I took out he shifter and it does not look to bad, but I have a loose pin in the tower, How do I get the pin out, do I tap it into the tower or tap it out towards the out side of the tower, Thanks Charles.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top