(800) 853-2651
SHOP NOW

Recent content by Chilidog15

Yesterday's Tractor Forums
  1. C

    9n no start after ignition switch left on

    I have a 6v system
  2. C

    9n no start after ignition switch left on

    My grand daughter sitting on tractor by mistake left ignition switch on. Now tractor won’t start. no spark. Where should I look for damage ?
  3. C

    Battery hold down for 9n

    I have a 9n with a hacked together 6v battery hold down system. I would like to install correct hold downs preferably as they came from factory. Right now there is none of the original hold down system on the tractor.
  4. C

    Re: Problem with Hydraulic Top Cover Rebuild - New Ram Cyli

    I had same interference problem replacing lift cylinder on my 9n.Had to angle grind some of front flange so bolt holes would line up. cylinder mounted and worked fine after that, I got my cylinder from nnalert. probably one manufacturer some where in world making these cylinders for the various...
  5. C

    9n crankcase vent

    replacing filter in crankcase vent cap.Is it supposed to be run dry or should I soak it in oil before install ?I bought a new cap and filter from this site.
  6. C

    9n-- thanks to all

    I want to thank all the regular contributors to this forum. I hope I don't forget anyone but Tim Daley , Kevin LaRue , Old Hoakie , JMOR have been especially helpful during my rebuild of the lift cylinder on my 9n. All the little tricks you guys have learned over the years working on these...
  7. C

    Weedeater primer bulb

    I have replaced primer bulbs .Obtained from small engine online parts companies like Jacks Small Engine. Easy to replace. sometimes you need to push the new bulb in using a certain sized socket wrench depending on the brand of your motor
  8. C

    9n pressure relief valve

    I am saying I am concerned that a batch of hydraulic relief valves have been made that have a bad dimension on the spring loaded end. It hangs up when inserted in the pressure relief hole. The little button shaped end measures bigger than other old valves I have laying around. Not the first time...
  9. C

    9n pressure relief valve

    have top lid off to rebuild lift cylinder.all went well. decided to replace pressure relief valve since everything all apart even though existing valve seemed to be Ok when viewed from side round plate.I had a new valve from nnalert. tried to screw it into pump but the plunger end would not go in...
  10. C

    Zane thing?/

    where can I get those white plastic blocks that the rod slides thru. Mine are starting to deteriorate
  11. C

    9n starter stopped working- 6v

    if i have to get a new starter , is the 6v/12v one sold on this site OK ? I want to support this site if possible .
  12. C

    9n starter stopped working- 6v

    after several starts and stops today starter quit working.Battery seems fine. charged overnite.All I hear a a faint clicking when starter button pushed.Cleaned terminals. Tried jumping with existing 6v .Negative directly to terminal on starter. Starter did nothing.The solenoid for this tractor...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top