(800) 853-2651
SHOP NOW

Recent content by classicxl

Yesterday's Tractor Forums
  1. C

    ford 7000 power beyond?

    Bought a new to me 7000 diesel, with only one outlet but has two other hoses coming from under seat capped off, one has no pressure when uncapped so I assume its a return and when other is uncapped there is pressure, Im guessing this is like a power beyond to run like a loader or something...
  2. C

    Ford 7000 follow up

    I just changed the injector pump oil. I ran the fuel way down and added new fuel today. Seems to run good.
  3. C

    Ford 7000 hyd oil

    I have a Ford 7000 and have always used hy-tran in it for hydraulic/transmission fluid. I have a 5 gallon pail of plain hydraulic fluid. Citgo is the brand name. Is it okay if I use it in it too?
  4. C

    Ford 7000 follow up

    When we got the tractor home we looked in the tank. We did not see any algae like the previous owner said. It would crank but not start and only run on a few short whiffs of ether. We traced the fuel lines and had fuel all the way to the injectors. We cracked 2 injectors and she fired right up...
  5. C

    Ford 7000 algae in diesel

    My dad, brother and I are in the process of buying a Ford 7000 for our hay business. It has sat for 3 years and now has algae in the tank. We would like to use it right away as soon as the weather breaks long enough to do some hay. Are there any quick fixes to get rid of this algae besides...
  6. C

    Farmall h piston/sleeves

    My son has a set of good used pistons but not sleeves he took out of a puller tractor to oversize it, hed make u a good deal, call lane at 989-295-5069
  7. C

    Hydraulic cylinder locking up on retract stroke

    You seem to think maybe in one of the couplers rathar than control of some sort huh? ( I hope)
  8. C

    Turns out it wasn't me after all.

    They only put auto trans in semi tractors so women have something to drive. lol, drove one for two weeks and hated it, try backing up hill slowly like to be able to bump a dock, one more way to get guys on road without knowledge or ability to shift a non synchronized transmission.
  9. C

    Hydraulic cylinder locking up on retract stroke

    Bought a new to me, older haybine last winter, with a like brand new tierod type lift cylinder with brand new hoses, when trying to lower cylinder( hooked to farmall 460) after it was used a bit, cylinder would stop anywheres in retracting stroke and will not continue until i stop tractor, and...
  10. C

    Log splitter repower

    got it, you guys are much more knowledgebale than I am with that stuff, had this for several years, and was never right, but everything yous say makes perfect sense. Maybe itd be the ideal pump for live power on my M instead. Back to the drawing board. thanks you guys!!
  11. C

    Log splitter repower

    Maybe its not a two stage pump, how can I tell, dealer who ordered it for me few years ago knew it was for a splitter but who knows. I no old pump would shear a 8 inch pine log crossways with a ten horse and this pump was told id need a 22 horse briggs but was a bit cheapee than the same size I...
  12. C

    round baler tying procedure

    I forgot you did say it had two tieng arms, id say you must start from center and work to ends, ull get used to it quick, theyre simple machines. Just make sure both tubes are feeding twine before you send them to outsides
  13. C

    Huge price increase

    I switched to propane a few years ago, uses more oxygen, but oxygen is alot cheaper than gas, a little harder to get lit when windy but once its lit its fine, ive even welded and brazed with it, put 50 pounds in a hundred pound tank and seems to last long time, propane tip was about20 bucks but...
  14. C

    Log splitter repower

    got a log splitter with a new pump that requires a 22 hp motor to run it, thought about running off pto from my M, how would best way to gear up pump to same speed as what Id have from a smaller gas engine so I wouldnt have tractor running wide open, didnt think itd use alot of gas at half...
  15. C

    round baler tying procedure

    sounds like you got it, ussually just before you got bale finished being rolled or formed swing down arm into center of pickup area and let some incoming material get hold and draw it in, this will also keep twine from wrapping around a roller instead of bale. once you see twine being drawn into...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top