(800) 853-2651
SHOP NOW

Recent content by CODI

Yesterday's Tractor Forums
  1. C

    ROYSE- carb help needed!!

    I do have it but I think the one that was on it was also an aftermarket one, but I'd have to check. I'm not very confident on rebuilding one though, but I guess I could always learn.
  2. C

    ROYSE- carb help needed!!

    Hey ROYSE! I am in severe need of your carb expertise. I have a carb that has been on my 8n for a couple years. It is from tractor supply and says it is 8N9510C IMPAF. I have had sputtering issues with it before but it seems to be getting worse. Gary mentioned to me that it is probably an...
  3. C

    Sputter and rough running 8n

    No. I can't remember what it said. It's been on there for a couple years and it's sputtered since its been on there. I will post to him and ask for help. Thank you!
  4. C

    Sputter and rough running 8n

    It is the one that is sold at tractor supply. It says it is an 8N9510C IMPAF. I'll post a picture when I can get a god picture of it.
  5. C

    Sputter and rough running 8n

    Does it make a difference if the carb that is on there is from tractor supply?
  6. C

    Sputter and rough running 8n

    Thanks Gary! I probably am making this much harder than it needs to be.
  7. C

    Sputter and rough running 8n

    Where is that located inside the bowl?
  8. C

    Sputter and rough running 8n

    I can pull the main screw all the way out with no change. As far as screwing it in, I usually can't screw it in more than 4 turns before it starts running really bad.
  9. C

    Sputter and rough running 8n

    Okay.... So I have tried adjusting the carb throttle intake adjustment.... No results. It runs good on a cold start but once it warms up it spitters and sputters and surges below 1000 RPMs. It also sputters going do hills, but cooing up it has plenty of power and doesn't sputter at all or surge...
  10. C

    Engine idle surge

    Nothing seems to help it. Out, in... Doesn't seem to matter. I am getting good flow through the carb and all filters look clean. There seems to be no problem above 900 rpm, however the main adjustment is adjusted extremely rich. Im thinking there is a vacuum leak somewhere....???
  11. C

    Engine idle surge

    I was kinda thinking that could be the issue. Out richens, right?
  12. C

    Engine idle surge

    Well...here I am again. This time not for the distributor! The one I got seems to be working fine. Now I am having an issue with the engine surging. It only does it however, after the engine has been revved up and I am backing the throttle back down to idle. One I get it down on idle, it...
  13. C

    Side mount dizzy

    Okay.... Hopefully this is the last post on this side mount for a bit.... I fixed the gear and on inspecting more I noticed it would turn for a bit then it would seize and I couldn't get it to turn with vice grips. The shaft seems to bent as well as the housing and the bushings don't seem to be...
  14. C

    Side mount distributor drive gear

    I'm having a hard time getting the gear off. Any ideas on how to get it off?
  15. C

    Side mount distributor drive gear

    Hey all..... I have found that the pin that holds the drive gear on the distributor of my 8n has sheeted. I am wondering if anyone knows where I can get new pins for it and what size they are? It's an 8N side mount
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top