(800) 853-2651
SHOP NOW

Recent content by Craig 59 641

Yesterday's Tractor Forums
  1. C

    3400 Holley carb

    Ford 3400 gasser with Holley carb. Is there supposed to be a spring on pin that holds floats in place. Took apart carb to check out and buy a rebuild kit. Down loaded a exploded view of same type carb. Shows a spring. Mine did not have one. Can t find any rebuilds that offer this spring with...
  2. C

    Ford 3400 running poorly

  3. C

    Ford 3400 running poorly

    I m confused if resistor wire is missing. Then shouldn t I have a resistor external or coil with internal resistor.
  4. C

    Ford 3400 running poorly

    Repairing a ford 3400 for a friend. Was running poorly. Wouldn t rev up. Another person replaced the stock Holley carb with ?? Not sure of. Had a gas leak they thought it was carb. So replaced it. Still had a leak. Called me into help. Found leak in fuel pump. Replaced it. Ran better. But had a...
  5. C

    Ford 3400 running poorly

    Repairing a ford 3400 for a friend. Was running poorly. Wouldn t rev up. Another person replaced the stock Holley carb with ?? Not sure of. Had a gas leak they thought it was carb. So replaced it. Still had a leak. Called me into help. Found leak in fuel pump. Replaced it. Ran better. But had a...
  6. C

    641 oil seal power steering

    Help needed looking for info on oil seal below control valve assembly on steering column. This goes in adapter. Part I'm told no longer available. Mine blue out in winter cold snap while plowing. Power steering oil ran down into sector gear box and out relief / oil fill cap. Pulled oil seal had...
  7. C

    641

    Go to a raditor repair shop if you have your original one and have it recored.
  8. C

    641D Possible to put a loader on this?

    I have a Dearborn trip bucket on my 641 4 cyl gas.
  9. C

    Ford 641 compression - what is too low?

    I have a 641 110 psi each cyl . Run tractor with front end loader. Back blade,York rake,4disk or brush hog. 3 to 4 times a wk with one or the other attachments. No smoke pulls all good.. Useing no oil between changes. I say your ok as is.
  10. C

    641 hyd 3pt down force.

    Question hydraulic s on my 641 should I have the same down force as lifting on 3pt hitch. My back blade usually floats over ground not digging in like I think it should. I rebuilt hyd pump with master kit from yesterdays tractor. It made mud work much better. Just wish I had more down force.
  11. C

    59 641 power steering breaking hyd cylinder !

    Update on cyl breaking been awhile. Ran using 1 good cyl. Bought 2 new 5/8 shaft cyl. Installed them. Lifted front of tractor. Removed tires. Pulled sector gear covers. Turned steering wheel till hubs looked straight. One was turned in slightly. Right side. Adj till straight. Then checked sector...
  12. C

    59 641 power steering breaking hyd cylinder !

    Makes sense will look into it more. This wk end. Think I just need to move pitman arm till even. Them see how steering lines up,. Adj drag links from there.
  13. C

    59 641 power steering breaking hyd cylinder !

    f you mean the pitman arms or drag links. Pitman arms are one slightly foward and one slightly reward. Drag links about same both sides. Wonder if left side Pittman is what needs to be moved
  14. C

    59 641 power steering breaking hyd cylinder !

    I too replaced my orig. Pump with new type from Yesterday's Tractor. Old pump don't share same relief valve. Can't swap them. Why would it effect one side only?? Unless I've got some adjusting to do. But then all I did was up date to new cyl. After orig one bent.. Only adj I know of is in drag link.
  15. C

    59 641 power steering breaking hyd cylinder !

    it was turning left cylinder bent when fully extended. As if pitman arm was trying to push it too far and wheel was at the stop. I adjusted the drag link a bit maybe not enough. My right side has no problems works as it should. ??
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top