(800) 853-2651
SHOP NOW

Recent content by Cris

Yesterday's Tractor Forums
  1. C

    Ignition switch wiring for a TE20

    I purchased a two position key switch to replace the worn out key switch on my '48 TE20. I'm not the best at navigating the wiring on this machine. The original switch looks to be a vehicle type ignition switch that has an accessory position, on, and start which I know is not original to the...
  2. Ultradog MN

    One armed loader for NAA

    Saw this on CL last night. Called the seller to see if he had the brackets for it. He didn't know so I described them to him. We texted some after that and he said all 3 brackets were all there. He updated his ad with more photos. These "One armed bandit" loaders are pretty cool and the...
  3. U

    Hay Storage

    I am looking for input on how I should finish off the floor of my pole barn where I will be storing hay. The hay will be stored on pallets, but under that what do I do? I don't know the exact terminology across the globe, but I was planning on putting in gravel, clean gravel, 5 inches thick or...
  4. B

    There! That sucker is fixed!

    The ancient Toro electric weedwhacker died the other day. This thing has been rode hard and put away wet for 20 plus years. Dismantled it and found one of the brush springs had been busted for some time. Cut up one of those foam ear plugs and added a heavy rubber band. Lubed it up while I was at...
  5. C

    cub battery

    hi I bought a 55 Cub today at auction. It has a 12 volt battery in it but still has a generator on it. It cranks real good but this concerns me for safety reasons should I be? Could this cause a fire or burn wires Thanks for your input
  6. C

    dirt scoop

    Did Farmall make a factory dirt scoop with a fast hitch on it? Bought one today with a little red paint left on it,but no identifying marks. This is for a 140 with fast hitch. Thanks
  7. C

    140 fast hitch adjustment

    So disk harrowing or bush hogging you need it loose so it can move freely and row cultivating tight and not able to move
  8. A

    mf 725 mowditioner

    i have a badger 1005 mowditioner which is the same as a massey 725 im in need of an operators manuel for it it is out of adjustment at the feeder rolls as it plugs up within 6ft of cutting also im in need of the correct belt tensioner spring for it too if you have a parts machine in the fence...
  9. C

    Super A rear wheel weights

    I want to remove my rear wheel weights on my Super A, I have soaked the bolts and nuts that attach them for a week in pb blaster and wd 40. I still can not break them loose with my air impact wrench or a pull handle (with cheater bar on it) Any ideas to try are greatly appreciated.
  10. C

    oil change

    thanks alot Rusty
  11. C

    oil change

    I have a Cub,Super A and an Allis B, I probaly dont run any one of these more than 10 hours a year max. How often would you recomend changing oil and filter and also do I need to use any fuel additives? (ie stabil,octane booster,etc) Thanks
  12. C

    super chief plow

    Is there a decal on each moldboard or only one? Thanks for your time
  13. C

    super chief plow

    I need the color scheme for a super chief moldboard plow. Have one I am trying to spruce up some. It is the fast hitch version (2-14s) and looks like a peice of a decal left on it. What is the proper location for the decal also? Thanks alot
  14. C

    mower belt

    I have a sickle mower on my Super A. It has a 5 ft cutter bar and also has 22 on the base. 2 questions Is this a model 22 sickle mower? and what type and size drive belt does it take? (from pto pulley to mower shaft pulley)
  15. C

    140 lift

    I have a 140 with fast hitch,my question is when finished using a rear implement (such as disk harrow or rotary cutter) should you leave in the up postion or lower it to the ground? Thannks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top