(800) 853-2651
SHOP NOW

Recent content by D Nickerson

Yesterday's Tractor Forums
  1. D

    JD 1050

    Well guys, I gotta say you got it right. I was getting 50 lbs. just cranking it. Needless to say I feel a little embarrassed. I've been working on equipment all my life, and I've never seen diesel oil so clean after a change. I've had this thing since '86 and honestly don't remember it being...
  2. D

    JD 1050

    I'll try to keep this brief. I finally brought it in for some needed work. One of the things I did was pull the bottom engine plate off to inspect the rod bearings. I could have sworn I started hearing a slight knock last year. With the plate off I could reach up and check 1 of the rods for...
  3. D

    Help identify

    I know this isn't a tractor, but some of you must know what it is. I mainly need to know what engine it is. This thing has changed hands and painted so many times, I can't find a tag on it anywhere. Thanks.
  4. D

    HELP!!!!

    As far as cross referencing, get the number off the filters that are on it now and cross it with a google search. Hope this helps Doug
  5. D

    Cub Plugs/wires

    Thanks, I appreciate it.
  6. D

    Cub Plugs/wires

    I'll be using it for cultivating, so it won't be used hard.
  7. D

    Cub Plugs/wires

    Whats the best plugs and wires to use for a '51 Cub with a Mag. The wires in the YT store don't say if they're solid or not. I thought I saw somewhere that Autolite 3116 plugs work(which are the ones I used to run in my JD A). Are they still a good non-fouling plug like they were 20 years ago...
  8. D

    Cub fender brackets

    Yeah, that's why I asked. I figured I could eliminate them to prevent it from happening again. That and finally get the dern thing out of the weather. I can't see a real purpose for it.
  9. D

    Photos of another splitting idea

    Nice Gantry. Here's what I use for heat. I have no problem getting it 80 when it's single digits out.
  10. D

    Cub fender brackets

    The more I look at these, the more I don't think it's factory, too big and square. I'll be darned if I can find any pictures of this area on cubs. Does anyone else's look like this? I want to get fenders cause they are rotted out behind both brackets. One picture I did manage to find didn't have...
  11. D

    MW clutch

    Ok, thanks for your help, I appreciate it.
  12. D

    MW clutch

    That's what I thought too, no matter the clutch position it should roll. The reason I asked was because the M&W sits right on the outside of the brake cover and is tied in thru the brake somehow. At least I think it is anyway. So if the M&W is stuck, most likely the brake is too, causing it to...
  13. D

    MW clutch

    Yeah, I know. That's why I've put it off this long.
  14. D

    MW clutch

    I'm finally getting a chance to do the head gasket on my MD that sat outside for about 10-12 years. My problem is the left rear wheel is locked up. So is the M&W. My question: is the axle locked up because of the M&W? It(axle) has a tiny bit of movement after bringing it up to my garage. I used...
  15. D

    Change magneto ignition to battery ignition?

    I agree with Randy, you can't beat a good mag. Sure they are more expensive, but that extra cost makes up for all of the dist/coil headaches. I've had a mag on my Oliver 60 for 20 years with no problems, knock on wood. As stated, you don't need full voltage for a mag equipped tractor to start...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top