(800) 853-2651
SHOP NOW

Recent content by Dalesbebe

Yesterday's Tractor Forums
  1. D

    2N 9N Front Spindle Not Keyed

    Quick response and excellent information. I knew it was an early 9N/2N just didn't know that early! Thank you.
  2. D

    2N 9N Front Spindle Not Keyed

    I am trying to figure out a PN for the steering arms on my 9N/2N. Per the assembly drawings, the steering arms and spindle are supposed to have a woodruff key but there is none on my Ford. In addition, the spindle arms are supposed to have a bolt and nut to keep the spindle arms attached but...
  3. D

    Bush Hog 2400 Front End Loader Bucket Cylinder

    I am looking for either an OEM PN or Conversion PN for the bucket Hyd cylinders. The stroke is 20 and the retracted length pin to pin is 34.5. The rod is 1.5 and the mount pins are 1. Anybody know where I can get the cylinders or where I can get the cylinders rebuilt? Thank you.
  4. D

    2N Hydraulic Pump Chatter

    All, Thanks for each reply. I will let the forum know when I finally figure it out. You guys gave some good things to check on.
  5. D

    2N Hydraulic Pump Chatter

    I have a 2N that sat for 8 years inside a garage with no lubricant in the rear differential or transmission. I have the engine running great, the PTO turns and the 3 point lifts and lowers. My issue is that when maintaining a lifted load (mower) in a position, it sounds like the hydraulic pump...
  6. D

    2N Hydraulic Pump Chatter

    I have a 2N that sat for 8 years inside a garage with no lubricant in the rear differential or transmission. I have the engine running great, the PTO turns and the 3 point lifts and lowers. My issue is that when maintaining a lifted load (mower) in a position, it sounds like the hydraulic pump...
  7. D

    JD 2440 RPMs Won''t Reach Rated

    DieselTech, Please respond to [email protected] about possibly rebuilding an injection pump. Thanks.
  8. D

    JD 2440 RPMs Won''t Reach Rated

    Thanks everyone. I guess I will pull the injection pump and send it in for rebuild once I find someone who can do it for a reasonable price. Anyone have any recommendations who to send it to?
  9. D

    JD 2440 RPMs Won''t Reach Rated

    All, I changed the glass square fuel filter on my 2440 and bled the filter. Started up the tractor and it ran fine. Mowed for about 25 mins then all of a sudden rpms dropped off to about 1600-1800 and would not go higher. Changed the fuel filter and bled again but not better. I removed the...
  10. D

    How do I Replace the Fan Belt on 2N?

    Thank you for the quick reply. I grew up in my dads garage and I have changed quite a few fan belts but I am new to 2Ns. Not a lot of videos on "how to" with regards to 2N or 9N tractors. Unfortunately, the belt is too wide to slip between the ratchet and the front motor support or...
  11. D

    How do I Replace the Fan Belt on 2N?

    Changing a fan belt on my 2 N should be easy but my crankshaft ratchet is to close to the front motor support to allow a new fan belt to be installed over the crankshaft ratchet. The lower bolts on the front motor support to engine are longer than the top bolts. This leads me to believe the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top