-
D
NOW ready to mow!
Wow! looks great Chris. Quick question.. why is it that no one paints alternators. I know you would have to cover the vent holes. just wondering, Enjoy mowing later. Dan -nyc -
D
Runs In Paint
Here is a link to valspars contact page on their site you may e-mail them and see if you can get help there on their product. HTH Valspars implement site contact info- Dan-nyc
- Post #1
- Forum: Paint and Bodywork
-
D
Flash Times
Thanks, Just sweating the details since this is my first time spraying "real" paint.- Dan-nyc
- Post #1
- Forum: Paint and Bodywork
-
D
Flash Times
I will be using PPG Omni. So if I take 30 min after starting to lay down the second coat that will be ok or do I need to re-coat right at/around the flash time? Thanks as always everyone"s knowledge is appreciated.- Dan-nyc
- Post #1
- Forum: Paint and Bodywork
-
D
Flash Times
I was wondering if someone could further my understanding of Flash Times. If the spec sheet suggests around 15 minutes. How much leeway is there. Since this is my first time I am sure I won"t be rushing it but How "late" is bad, or how can you tell your too late? Thanks!- Dan-nyc
- Thread
- Replies: 5
- Forum: Paint and Bodywork
-
D
y'all badgered me into a grill for the 4600
Hey Soundguy, You may be able to cover up the "problem" with the grill iff you add a nice loader... LOL Dan --nyc -
D
950 near hyd disaster
Soundguy, I saw the chipped paint and could feel for you there. Great to hear the solution was "at hand", a little work and knowledge goes a long way! Congrats on your success. Dan --nyc -
D
loose lower 3pt stud on rowcrop trumpet
Hi Chris Here is the other Diagram I have. Dan --nyc Actual 4d1 diagram -
D
loose lower 3pt stud on rowcrop trumpet
Hi Chris, These may be what you have but if not here are 1 diagram. and I'll post a second in a min. HTH Dan --nyc diagram 4d1 -
D
800 series grill
Thank You all!!!! I will get a chance to look things over this weekend, and now I know what I should have had and can figure out the proper solution. Dan -
D
800 series grill
Hi, I am restoring an 860 and wondered if anyone has any info/photos of the way the upper bolts for the grill thread into. Hard to explain but the wing nut like bolts thread into someting that the previous owner did not leave in place and I would like to see what I should do to fix/restore...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy