(800) 853-2651
SHOP NOW

Recent content by Dick M

Yesterday's Tractor Forums
  1. D

    OT-JD v. Kubota v. New Holland

    I have owned a New Holland TC35D with loader and shuttle tranny for 8 years 900+ hrs Only breakdown or problem I have had with it was the safety switch under the seat broke. If I ever buy another new one, it will be a NH.
  2. D

    I did it! replaced the tube, now how much Calcium?

    Last fall here in Central Nebraska, H took my 10X28 tire to the local CO OP They charged me $39 plus tax for the Tube and installed it with no labor. Guess I got lucky for a change.
  3. D

    PB Blaster vs Kroil

    I was wondering what is the preferred penetrating liquid. PB Blaster, Kroil, or someting else.
  4. D

    PTO seal

    I appreciate your input, but I just don't feel the need tu spend money on something I don't need. I have a New Holland TC35 and use it for everything that needs a PTO. The 2 n is just for pulling the cultivator thru the sweet corn. Dont want to adjust the wheel spacing on the tc35.
  5. D

    PTO seal

    Yes its an eazy job to R&R PTO assembly. But like I said my shaft is worn and needs replaced. I donn't replace everything that is wrong with the 2n I have a 2 n for everyday usage, It's not a show tractor, like I said I don't ever use or need the pto WHY REPLACE IT>
  6. D

    PTO seal

    The open side goes to the oil. My 2n has a shaft that is so worn that it still leaked. I don;t use the pto, so I put some teflon tape on the pto cover and it doesn't leak anymore.
  7. D

    8N troubles followup

    The first thing I would do is take out the thermostat
  8. D

    Generator adjuster

    Trying to upload pic again
  9. D

    Generator adjuster

    Here is a pic of mine. Am rebuilding and have not put it back on yet. Hope this helps
  10. D

    How do I fix broken metal valve stem, rear

    Tubes are not expensive. The problem with old tubes is that a lot of time they stick to the rim, or the stem twists out of the tube when trying to take it apart. I was lucky. My local CO-OP Sold me a tube for $39 and installed it for free. While it is apart, I would recomen that you wire...
  11. D

    Tip in re attaching engine to transmission.

    When getting ready to reattach the engine to the transmission, I cut the heads of of a couple of 4 inch bolts and screw them into the engine for use as guide pins, to the tranny. Saves a lot of work trying to align things especially if working alone. I know many of you probalby allready know...
  12. D

    She runs!!!! Oil pressure question....

    Paul I am ready to install the engine. and want to Prime the pump. How much gear oil should I put in the pressure relief opening?
  13. D

    Carb from Gary

    I see you painted your 2 n red / grey. When I bought my 2 n, it was also red /grey. SO I decided to keep the red grey combo. To each his own.
  14. D

    extra part?

    Thanks for all the help. At least its not something thats vital to the engine. YOur help is greatly appreciated
  15. D

    extra part?

    I didn't take the bendix apart. I just don't remember that washer when I was taking it apart. I have a photographic memory, but as I get older, I seem to run out of developer
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top