(800) 853-2651
SHOP NOW

Recent content by dmartin

Yesterday's Tractor Forums
  1. D

    john deere g oil pressure

    Did you check the gauge on another tractor ?
  2. D

    poulan2150 no start

    have good spark fuel lines have been replaced carb cleaned and still will not start even with starting fluid
  3. D

    sale at expo in Waterloo

    Mark- do you know what the BO Lindemans went for ?
  4. D

    1950 8-N

    Randie- are you saying that the starter does not run after it quits or that the starter runs but the engine will not start ?
  5. D

    seating rear tires - HELP!!!

    Had the same problem. Pumped them up to 50 lbs. and they seated.
  6. D

    Which F model should I buy?

    I've got a narrow tread Regular (in Ma.)on F&H round spokes that is a really good tractor and needs a new home.
  7. D

    washer or not?

    Not "correct" but I like to use brass/bronze nuts. They will always come off easy.
  8. D

    splitting rocks

    A propane torch will not work. We use oxy/propane to freshen up the surface of recyled cut stone. glennster is right. Pins and feathers will reduce any size stone down to a workable size. If it's in a hole just dig around it to make room to drill the holes.
  9. D

    O.K. something don't look right with these pistons (PIC)

    Get your bore clearance correct if you use the aluminum ones. Many, including myself, have had problems with them seizing up when the cylinders were not bored to the right clearance.
  10. D

    G governor howl

    Greasing the fanshaft up front won't cure the back bearing. Still bettin the rear fanshaft bearing is the culprit.
  11. D

    G governor howl

    It sounds like the fanshaft may be the cause of the howl. The bearings in mine were shot and it made alot of noise.
  12. D

    Unstyled Hoods

    Got a hood for my unstyled G from Dave. His work is excellent and the hood is perfect.
  13. D

    John Deere #52 Plow

    Thanks. I found a set in Penn. and have them headed this way. Thanks for the offer.
  14. D

    John Deere #52 Plow

    Thanks Charlie. Do you have one of your old ones still kicking around ? Never thought that a dealer would have parts. Will try that too.
  15. D

    John Deere #52 Plow

    Just started to restore/repair a plow for going to plow days. It has the Syracuse 1451 NF moldboards and one of them is missing "chunks" and cracked. I'm guessing that it probably cannot be welded. Is it likely that I will be able to find a moldboard and chin if I search around ? Thanks.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top