(800) 853-2651
SHOP NOW

Recent content by DMont

Yesterday's Tractor Forums
  1. D

    DT466 OIL PUMP

    I don't have plans to compete with this tractor, just wanted to use the larger oil pump. I could use it with the truck frnt case, but this would create the need for building engine mounts. Thanks for your reply.
  2. D

    DT466 OIL PUMP

    I don't have plans to compete with this tractor, just wanted to use the larger oil pump. I could use it with the truck frnt case, but this would create the need for building engine mounts. Thanks for your reply.
  3. D

    DT466 OIL PUMP

    Please, ( actual users ). The DT466 oil pump is a geroter style that started as a narrow 5/8 width gear. The gear used by the farm equip. division now is 1 inch. The oil pump is mounted on the frnt of the crank and is driven at crank speed. Has anyone used the larger 1.240 width as used by the...
  4. D

    IH DT 466 Oil Pump

    I find it almost funny that there will be post by persons that know absolutely nothing and do not do any research before making totally incorrect statements. DT466 engines are part of the 300-400 series used in construction equipment, farm equipment and extensively in trucks. The guys here on...
  5. D

    IH DT 466 Oil Pump

    What is the width of the oil pump being used on DT466s turning high RPMs. When using the wider pump was the larger suction area frnt case and larger suction tube used? What has been the general experience here???
  6. D

    Oil Brands

    I feel its more important to stay within a certain oil API classification than to stick to particular brand names. So if the oil you have been using meets a severe service API classifaction you should make sure the substitute oil meets or exceeds the same classifaction. The engine manufacturer...
  7. D

    O/T Shop Buildings and Barn Builders

    Just curious to your location. D & J metal bldgs in Colbert, Ok 580- 296-2643. They have built several for me and no complaints. 50 x 100 and larger. Delephine or Terra.
  8. D

    O/T Shop Buildings and Barn Builders

    I know several in the Sherman area, how close are you?
  9. D

    986 torque amplifier

    You don"t necessarly need to use the gear locators for the Hydrualic and PTO drive shaft gear. The MCV needs to come off and have new springs and orings installed which will allow you to realign the gear in question on reinstallation. I definately would go with an Allied TA and they also have...
  10. D

    OT Welding Question

    That bracket is important enough to justify getting a guy that can weld vertical to come out and get you started if not weld it entirely. Your money will be better spent there than repairing it again. Get some pieces of metal, position them in a vice and practice with someone that can weld...
  11. D

    1586 questions

    The 1086 series IH had two gear pumps up until 1979 and some into 1980. They were open center and starting in 1980 IH went to closed center systems, on these models. The 1486 series tractor is the same as the 1086 except for the 436 engine in the 14. The gear pump models had a 12 gpm pump that...
  12. D

    MORE 985 TRANMISSION QUESTIONS

    The only way to really tell is to look for teeth in the trct rear frame and/or pull the cover plate to the range trans. You will need to jack the cab up to actually get it out. I know its a bear because I just finished one. I'm not sure you can get a prybar to the pinion shaft thru the left...
  13. D

    986 tramission more questions

    The park pawl engages the reverse driven gear to hold the tractor when stopped. You will need to remove the HiLo shifter cover to replace the park pawl. If the Reverse driven gear has teeth missing you probably will find some of them in the bottom of the case where the rear hyd pump is located...
  14. D

    Dt 466 truck motor differences??

    The truck motor went to a "C" series in about 1986 or 1987. That can be verified by checking the serial number. The C series improved the cooling in the head, wider bearings on the crankshaft, 1.250 width rotor in the oil pump, an MW series Robert Bosch injection pump ( which the tractor...
  15. D

    DT 466 vibration dampners

    Does anyone have experience with vibration dampners on a IH Dt466 engine. I am putting a DT466 in a 1086 and would like to use the dampner from the DT 414 along with the DT 414 flywheel. I have about decided to use the truck front case along with the MW pump. There would be a need to build...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top