(800) 853-2651
SHOP NOW

Recent content by doehmke

Yesterday's Tractor Forums
  1. D

    MF35 Hydraulics

    Yeah, that’s a good point. I always drop attachments before walking away for that safety reason. Anyhow, I picked up The Massey Ferguson 35 Tractor Workshop Service Manual by Chris Jaworski Found it on Amazon. Lots of good info and pictures.
  2. D

    MF35 Hydraulics

    I ordered this one from someone selling with the same photo on eBay. Description said it?s a reprint of the original. Seller had pictures of a few pages and the photos look ok from what I could tell.
  3. D

    MF35 Hydraulics

    Thanks, David. I adjusted that a few years ago after replacing the cylinder and it would lift an implement ok. But drop right away and quickly after shutting down. Never had it quite right, but it worked. Perhaps some wear now and it requires a more precise adjustment. Perhaps I can get it...
  4. D

    MF35 Hydraulics

    My MF35 has rear-end hydraulic fluid seeping out the relief valve on the left front of the lift cover. And the lift arms raise without an implement, but not with one attached. The lift had raised fine for some years after I replaced the pump and cylinder. Though it always dropped quickly after...
  5. D

    MF-35 3-Point

    It’s locked back. Used to work fine.
  6. D

    MF-35 3-Point

    The three point hitch on my MF-35 raises when there’s no implement hooked up. But cannot raise an implement. Just raising and lowering the empty arms causes oil to come out the relief valves on the top cover near the oem 2-lever control valve. I’ve read the shop manual, but don’t quite...
  7. D

    Weight - F20 Engine?

    Thanks, guys!
  8. D

    Weight - F20 Engine?

    Anyone know the weight of an F20 engine (complete). I need to get a quote for shipping one to see if its worF20 it instead of a looong road trip.inThis one has the starter setup. Thanks, Dan
  9. D

    IH 2A Hay Crimper

    Thanks guys.
  10. D

    IH 2A Hay Crimper

    I just picked up an IH 2A Hay Crimper. I see where a hydraulic cylinder would attach, but not sure how it would mount into the slot on the tongue end of the cylinder. Doesn't look like a pin would hold the cylinder in place. Also, can I use it manually without a cylinder? Thanks, Dan
  11. D

    Shipping How-to?

    Can anyone give me a general overview of how shipping works with a reverse auction freight company or standard freight broker? I have posted already to the hauling schedule, but am also wanting to check these other options. Not sure how they work. In this case it's only two tractor rear...
  12. D

    JD Sickle Mower No 8 and New Idea Hay Crimper

    Thx, Bob, for the diagrams and everybody else for the comments. Once I knew what to look for did found a lot of images on google for mowers 37 and 38 and new holland. I only have about 10 acres and looking for a reasonable altenative to putting more money into my oversized and almost entirely...
  13. D

    JD Sickle Mower No 8 and New Idea Hay Crimper

    I talked to a gentleman today who used to pull a pto driven New Idea Hay Crimper hooked to the back of a JD #8 Sickle Mower. He said the mower had a small hitch and the pto shaft came from the tractor to the mower and on through to the hay crimper. All one continous line of PTO power. Anyone...
  14. D

    F-20 Belt Pulley Nut

    F-Dean, My email is in my profile for doehmke - can you get to that? I tried finding your email in the memberlist but it came up blank.
  15. D

    F20 battery / starter trouble

    NAPA?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top