-
Stalls going uphill
I had the same problem and finally cured it by going back to the original old brass float. -
What's up with the silver paint vs original color on the rear wheels of otherwise nicely restored Ford tractors? Collectors, please weigh in.
I just got my NAA. Hoping mine will look as nice as yours someday! Great work.- Dogsix
- Post #51
- Forum: Paint and Bodywork
-
Just thought I would let you know since you responded that I got the tractor running today and...
Just thought I would let you know since you responded that I got the tractor running today and it was out on the valve timing by a tooth on distributor. Also the points needed adjustment. I got it running fairly well with the Chinese carburetor but not while on an incline. Bought a kit for the...- Dogsix
- Profile post
-
Introducing myself
Yes the previous owner had installed a add-on electric fuel pump. I removed it before I did anything else with it. I check fuel flow by removing the plug in the bottom of the carburetor bowl -
Introducing myself
Ok I’m beginning to understand now. Can I drill this by hand drilling or is this a job for a machine shop? -
1953 Ford Jubilee carb/ fuel trouble
I would start by pulling the 3/8” plug in the bottom of the carburetor bowl and catch it in a pint jar. It should flow strong enough to fill it in about 2 -3 minutes. If not there’s a restriction somewhere. There are probably 3 screens on that line. 2 at the sediment bowl and one inlet fitting... -
Introducing myself
I don’t think my carb. Is the same as yours is it?? The tube is not as long and it’s a 134CID -
Introducing myself
I have done all that already. The outlet of the tank (which is a new replacement) is at the back end (nearest the driver) and I pulled the sediment bowl and inspected. It was clean and like new. -
Introducing myself
Well I’ve been busy with the tractor since getting all the help and suggestions from you guys and thought I should give you an update. I now have it running really good. Starts easy and runs pretty well and has good power. Governor linkage set correctly ( I think). I pulled and re-installed the... -
Introducing myself
That’s one thing that I haven’t done. I’ll try some. I’m sure they have been flooded with gas several times. Thank you. -
Introducing myself
I’m going to try to get her timed next. Thanks for your interest. Previous owner gave me what he said was the old carb and it’s a marvel shebler 355 which I think is for a 8N . So I’m not planning on trying to use it. -
Introducing myself
Okay y’all. Here’s where I stand with my NAA. I can get her to start and run. She idles and runs full speed but the moment you put any load on her she stumbles. Here’s what I have done as far as troubleshooting over the last week. 1. Checked air breather oil and inspected for mud dobbers. 2... -
-
-
Introducing myself
Understood. Because of my newbie status I didn’t know if it was acceptable for me to go off topic like that. I will feel more comfortable as I learn the ropes here. I like the low end torque produced by the 300 6cyl.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy