(800) 853-2651
SHOP NOW

Recent content by dtubbs

Yesterday's Tractor Forums
  1. D

    case 300

    Does anyone know if a frost plug heater can be installed in a case 300/310 w/gas engine or if not a tank heater or maybe a magnetic heater. Thanks, Dennis
  2. D

    case 1070 brake sticking

    Case Nutty Only reason I didn't want to buy new springs is because the new ones I put on the 686 from the case ih dealer weren't very good. One broke while installing it & one fit loose. When I took the loose fitting spring back (no tension) the parts guy threw it back in the box w/the other...
  3. D

    case 1070 brake sticking

    Case Nutty The springs, discs & boot look very good so just going to replace the balls. I forgot about cleaning the splines too but I will. Never had a problem w/the parking brake. Thanks for your help, Dennis
  4. D

    case 1070 brake sticking

    I'm putting new brake actuating balls on my 1070 because the left one sticks & old balls are rusty & are probably original. Everything else looks good including no leaks. My question is do I leave the balls & seats dry after cleaning the seats. I had the same problem on our 686 IH & new balls...
  5. D

    jx95 rear final drive seal

    Does anyone know how to change the rear final drive seal on a jx95. The wheel & hub are off but I'm not sure how to remove the snap ring to get to the seal. It's not your typical snap ring. Any help appreciated. Thanks, Dennis
  6. D

    686 310 engine injector sleeve

    Thanks Pete. Dennis
  7. D

    686 310 engine injector sleeve

    Need to replace an injector sleeve on 686 with 310 engine. Will 3/4" tap work ok? Thanks, Dennis
  8. D

    686 310 engine injector sleeve

    Does anyone know what size tap I need to remove injector sleeve on 310 engine. Thanks, Dennis
  9. D

    686 310 engine compression

    thanks allan.
  10. D

    686 310 engine compression

    thanks tractor vet. think I'll leave it alone as it does run good.
  11. D

    686 310 engine compression

    Does anyone know what the engine compression should be on this engine & what kind of gauge to check it. Injectors are out so would like to check the compression. Thanks, Dennis
  12. D

    686 injector removal

    Scott I don't have a slide hammer anyway or the tool to put the sleeves back in so I'll try taking them out by hand. Thanks, Dennis
  13. D

    686 injector removal

    Dieseltech Air cleaner is good so it looks like the injectors need to be pulled. Do I need a slide hammer to get them out if they're really stuck. Dennis
  14. D

    686 injector removal

    need to remove fuel injectors from 310 engine on 686 & have them checked. i know these engines smoke but ours smokes a lot, even under full throttle. it's not using coolant or oil. what is the best way to take them out. any special tools required. i know the coolant should be drained from the...
  15. D

    1070 powershift

    Didn't here any grinding when shifting the range lever w/clutch depressed, just a clicking noise coming from under the power shift cover. All other tractor functions work. Thanks for your reply AgriKing. Dennis
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top