(800) 853-2651
SHOP NOW

Recent content by ducky 55

Yesterday's Tractor Forums
  1. D

    farmall m hydraulics

    I'm in the process of putting a new 2 spool valve for the loader on my M. The problem I'm having is I took the old valves and hoses off and I'm not sure how to run the new hoses. The tractor has a pump ahead of the distributor. Do I just run the hoses from the 2 fittings on that pump or do I...
  2. D

    hydraulic fluid

    Can anyone tell me how much hydraulic fluid it takes to fill a 1946 Farmall M with a loader? Also what do you recommend for hydraulic fluid? Thank you.
  3. D

    rear axles leaking

    I should've said I have all the accessories, fuel tank, steering and other parts. I haven't got the rear tires off yet.I'll take them off this evening and see what I got.
  4. D

    rear axles leaking

    Well i changed the gear oil in my M and both rear axles are leaking by the ends and it is leaking from the plate that is behind the belly pump?. Are these fairly easy fixes? I have the rest of the tractor tore down getting it ready for a fresh paint job so I would like to get these leaks fixed...
  5. D

    hydraulic valve replacement

    Thanks for all the great info. I found one that they say I can adjust the psi on, so i'm going to try one and see how it works. Again thank you all for the great info. Hopefully I can get this M working again.
  6. D

    hydraulic valve replacement

    I have a live hydraulic pump at the distributor. The valve control I am looking at a 2 spool, 21GPMflow used for open center systems.It has an adjustable relieve valve range: 1500 to3625PSI.Is this something that will work for my loader? Thanks again for all the great information
  7. D

    hydraulic valve replacement

    I want to replace my old valve controls for my loader on a M. Can anyone tell me what size I can use as far as GPM and PSI? Also would you recommend a 2 lever or a joy stick? Thank you in advance.
  8. D

    paint can primer

    Would I have to remove the primer I put before putting epoxy primer on?
  9. D

    paint can primer

    I'm starting to repaint my M and put some red oxide primer on the gas tank that was stripped to bare metal. Will this last after I paint it? The primer was Majic brand in a spray can. I'm planning on putting Majic brand on with a spray gun.
  10. D

    farmall m not ruuning well

    Would you recommend buying a complete distributor or would i need just the bushing and washer kit? And what is the difference between a IH and a Delco distributor?
  11. D

    farmall m not ruuning well

    Well I did a compression test tonight with #1 at 125, #2 at 125, #3 at 120, and #4 at 115. Anyone have a suggestion on what to do next, replace distributor shaft, check valves,different plugs? I have spark to each plug but it will not start. I'm at a total lose on what to do. Also is the...
  12. D

    farmall m not ruuning well

    Good morning Gene. I don't have a compression tester. I'm going to look for one today? Do you know why the engine wanted to die when i pulled the wire on #4 cylinder and not the others?Thanks.
  13. D

    farmall m not ruuning well

    I went out tonight and pulled each plug wire from the cap and reinserted a little and then pulled the wire from the spark plugs one at a time, Number 4 cylinder was the only one that killed the engine when pulled.It seemed like the engine ran a little bit better when I just started to put the...
  14. D

    farmall m not ruuning well

    checked the plug wires and there was spark on all the wires when i pulled them from the distributor cap. There also was as good flow of gas out of the carb. I did notice the distrutoer shaft wriggles from side to side. Is that normal? I ran it today and it missed and after about 45mins. of use...
  15. D

    farmall m not ruuning well

    I have been having trouble with my m running poorly, so I put in new points, condenser, plugs and wires. It still seems to have a miss in it. Today when I was using it it got worse, missing and running poorly with very little power. I increased the throttle and it got worse with the missing and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top