(800) 853-2651
SHOP NOW

Recent content by Eric Lee Peltier

Yesterday's Tractor Forums
  1. E

    TO 30 12v conversion

    I used the kit from this site and the alternator does not require a regulator as it is built in. You will need a coil but I bout one of the nice oil filled ones from this site and it burned out within 2 months and I put the original 6 volt one back on and it has been on now for 1 1/2 yrs and...
  2. E

    TO-30 Carb Leaking Gas

    Actually I was just told that a couple hrs ago and to tap the float bowl with a brass drift or similar item and it will get the float un-stuck. This did work and I am not sure why it happened but it does work right now which is an extremely good thing considering the gas was leaking almost onto...
  3. E

    TO-30 Carb Leaking Gas

    Ok, I know the subject is not a great description of the problem. So here is what is going on. I just completed numerous repairs and restoration jobs on my TO-30. I had planned on swapping out a carter carb that is original on my tractor for a TSX carb but turns out someone configured that TSX...
  4. E

    Re: Original Crank Handle TEA20

    If you are talking about the hand crank starter I believe this site sells them but obviously they are not original and probly made in India or Malaysia.
  5. E

    TO 30 Carb

    Where do I get a rebuild kit as the original is the other (carter) style carb and the only kit I can find is for the TSX 458.
  6. E

    TO 30 Carb

    The old carb fits the new manifold anmd yeas the old manifold was in really bad shape and leaked at the rear exhaust port and extremely pitted everywhere else waiting for more leaks. I bought the new carb end of last year so unfortunately it is too late to send back. On the bottom of the carb it...
  7. E

    TO 30 Carb

    I recently started some repairs including a new intake and exhaust manifold and planned on replacing the carb. I had bought a nice rebuilt carb on ebay a TSX458 which according to everything I have seen is correct for a TO 30. I had bought the intake/ exhaust manifold from this site. However the...
  8. E

    Oil Seals for Stearing Gearbox

    I just got the seals for my TO 30 and they dont look like the ones on your TEA20 but they are right for my TO 30. In case someone else needs the number & brand the only ones I could find locally were SKF #13027.
  9. E

    What type of Engine Oil should I be using in my TO 30

    Ok I actually run Rotella in the transmission/ hydraulic set up, I also have a bunch of Rotella in the garage as my previous truck ran that. Normally should I change that for a thinner oil then when the snow starts flying. Average winters here are 15F-25F but last winter was really cold and...
  10. E

    What type of Engine Oil should I be using in my TO 30

    So 10W 30 would be better? I live in N.E. Ohio and I changed it last winter when it was quite cold and (lake effect) snowing a ton. It really doesnt need the oil change yet but while it is down I wanted to get it done again.
  11. E

    What type of Engine Oil should I be using in my TO 30

    I am doing several repair & maintainance things on my TO 30 including new radiator, water pump, intake manifold, tune-up, oil change and stearing gearbox. My owners manual does not say a specific type of oil to use but when flushing the engine to use 10W oil. Last time I used 5W30 but am...
  12. E

    Oil Seals for Stearing Gearbox

    I am redoing the stearing gearbox on my TO 30 as the stearing wheel shaft bearings broke. It appears the the bushings are ok where the stearing arms come out of the gearbox but there has always been a slight oil leak at the arms. While I have it apart I want to replace the seals. According to...
  13. E

    TO 30 Steering

    Ok I have everything taken apart except the dash off but the dash and stearing box are off and the gears apear to be good. I need to finish taking it apart to be sure but it appears to either be the bearings in the shaft or the shaft gear. I guess it is a blessing in disguise as I had other...
  14. E

    TO 30 Steering

    So would it be a good idea to just order the bushings and the steering shaft bearings?
  15. E

    TO 30 Steering

    So what kind of can of worms am I about to open up by tearing this apart. I looked in my owners manual and there isnt much in there other than a basic diagram/ picture. Unfortunately I dont have a repair manual either. I am very mechanical but have never worked on something like this before so...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top