(800) 853-2651
SHOP NOW

Recent content by Eteda

Yesterday's Tractor Forums
  1. E

    what front end loader and how for MF 250

    looking at buying a 1985 MF 250. It does not have any hydraulic boxes or lines etc. for front or rear attachments that I can see or have seen. I am wanting to put a front end loader on it in the near future. the seller mentioned you couldn't put one on it because it did not have the hook ups...
  2. E

    help, MF missing pre filter or wrong engine, pieced together tractor?

    went to look at a tractor today pre purchase. MF 250. no pre filter. could not see where one should be. rubber gas line no copper molded factory line. a few things different from the previous MF 250 I had for 15 years. Tractor serial# 625047. Engine Serial number CE22488U736239L. The man...
  3. E

    Left break lever

    for now I'll put the project on hold because of the coming hurricane, or two.
  4. E

    MF65 - Oil dripping from Dip Stick hole

    My lift pump diaphragm busted and was pumping diesel into the crankcase causing oil to shoot out of the dipstick hole because it was over full. Thankfully I saw it when it started shooting out. I drained the crankcase to remove the diesel until I had time to replace the fuel lift pump a few days...
  5. E

    MF 200 loader

    I would like a FEL for my MF 250. What models do I search for How do I know what will fit it and what is to big for it to handle.
  6. E

    Left break lever

    thank you David P. of South Wales, I wasn't clear with my questions so Ill try to do better this time. do I half to take off the tire and fender, which ain't so bad. But the auxiliary remote valve, it looks kinda complicated. do I need or half to remove it also. it looks like a booger to...
  7. E

    Left break lever

    MF 250 wet brakes. what is the best way to remove the left brake lever. I think they are rusted up and causing my breaks to lock up. I removed the right one. cleaned it up and installed a zerk fitting. that seams to have un seized the breaks. the tractor now skids to a halt about two feet on the...
  8. E

    MF 250 replacing the top-hat seal

    I have drained the fluid and am replacing the top hat seal on the break rod and in the lever bracket. I installed the top hat seal in the bracket, replaced the gasket and mounted it on the tractor. I cant get the top hat seal over the first ring to get it seated properly so as not to leak. I...
  9. E

    Block number

    On my Massey Ferguson 250 Perkins 3cyl 152, it appears that my engine serial number is part of the block number. I think a lot of people consider them the one in the same. It also has a tractor serial number stamped on the metal plate in its place where it should be. Its a little confusing until...
  10. E

    MF 250 break lever pin rusted

    Thank you so much DavidP, I will give it a try. I've decided to wait until all the parts come in before attempting to heat it up or remove the lever support. I found the yellow MAP gas. Ill try a pair of vice grips on it after I heat it up a little. If that don't work I heat it up a lot. if that...
  11. E

    MF 250 break lever pin rusted

    David P, the brake lever moves freely. the brake rod, that passes through the brake lever moves freely. the only thing that is still rusted and will not move is the break leaver pin that attaches it to the break lever support. When I move the lever back and forth by hand, the pin moves with...
  12. E

    MF 250 break lever pin rusted

    DavidP, South Wales, I'm sorry I have to ask, but why cut the rod? will the lever and the lever support not just come away from of the housing and slide off of the rod, if I take the two bolts off the lever support? I have taken off the adjusting block and adjusting nut (#8 & #9) in fig. 163. Is...
  13. E

    MF 250 break lever pin rusted

    I have figured out that the break levers(#7) are rusted in all three places and will not allow the breaks to release. I've worked both of the break rod pins loose and disconnected them on the right side. I will have to do one side at a time. In the manual MF-42, page 62, fig. 163, the top pin in...
  14. E

    Massey Ferguson 250 break leaver

    My breaks leavers are rusted up. the pin is rusted to the inside of the leaver. I have no torch or welder to heat it up with. can I just take off the break leaver support and press it out or use a punch to drive it out or replace the leaver. My main question is will break oil leak out if or when...
  15. E

    Model number and tractor info

    Thanks ptfarmer yes I'm in North America gona go look at the site now.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top