(800) 853-2651
SHOP NOW

Recent content by Ethan Chamberlain

Yesterday's Tractor Forums
  1. F

    Farmall 504 steering wheel seal

    Hi guys new to the site. I have a 504 that I got a seal kit for and it doesn't fit. Been searching all over to find out what I need. I pulled the steering wheel and there was a snap ring then a seal. # C/R 374527 R91 . The kit had 3 parts spacer, seal, dust cover. The spacer and seal are smaller...
  2. E

    John Deere 4200 plow cylinder

    Hello I bought a john deere 4200 plow that was missing the cylinder to flip it over. I didnt think much of it till i learned that it is a john deere special one, a 3 - 5 1/2. I cant seem to find another supplier for it other then john deere itself, but its a 500 and some dollar part through...
  3. E

    820 two cylinder miss

    Hello, Ive got an 820 here that to me acted like it had blown a tip off an injector. It smokes alot of grey/brown smoke with raw fuel coming out the stack and spotting up the operator and the sheet metal. I pulled the injectors and they looked fine and tested good at 2300 psi. So now i geuss its...
  4. E

    Were the gas start diesels harder to crank?

    If the decompression lever,rods,and valves are all working then the IH gas start diesels are not any harder then a straight gas tractor to hand crank. I have seen a few of the pieces that are under the valve cover that open the valves break in the past. When that happens, you can no longer...
  5. E

    Bad news on 7520 Jd

    I'd bought the neighbors 7520 John Deere earlier this year with the intent to pair it with my crust buster disk, but now I'm not sure what to do. He had retired two years ago, and this tractor has sat since then. I had to put great deal of time and a considerable expense into it to just get it...
  6. E

    7520 John Deere

    I bought a 7520 John Deere this last winter, and am just getting around to trying to get it to start. The guy who had it retired last year, and didn't use it the last two years he did farm. I've never been around one of these 7520's before, but am familiar with the 4020's, 3020's. This tractor...
  7. E

    Rebuilding pioneer conversion hydraulics

    Are the parts available to go back to the John Deere couplers and do away with the conversion ones?
  8. E

    Rebuilding pioneer conversion hydraulics

    It was a nice warm day here today, so I started on rebuilding the number one scv couplers on my 4430. I've got the I&T manual for it, but my tractor has had the pioneer conversion kits put in. I got the O-ring and seal kit from John Deere here in town, but the kit came with page two only of the...
  9. E

    Cenex machinery warranty

    I"ve been considering enrolling a couple tractors under the cenex total protection/extended protection warranty, and was curious about people"s experiences with the program. Good or not so good? Thanks
  10. E

    Steam Engine

    There's many aspects to valuing a steamer. Depending on condition, completion, and make/model it has the potential for being worth something. If its just a boiler that has been in a spillway for decades being target practiced at its scrap value. As far as a specific value if its complete, I'm...
  11. E

    560 diesel vs case 830 diesel c.o.m.

    My pick would be the 830 case. I've never had very good luck with the 560's between the TA's and the tendency for them to eat sleeves. I've ran three 560's for various duties, and not a one had a TA that was good. Another kept on breaking the top ring on the sleeves and gradually worked them...
  12. E

    1566 steering delay problems

    I"ve got a 1566 ih that will not steer until it sets running for about ten minutes while I crank the wheel around. I normally just deal with this issue, but I am curious as to what the problem is? The oil in the transmission is not milky like it has water in it. Anybody know what"s happining?
  13. E

    1066 Clutch

    I am just finishing a clutch job on a 966, and the parts bill for me was around the 825 mark if im thinking correctly. It got a new pressure plate, clutch disk, rear main seal, throwout bearing, IPTO shaft, and all the front transmission seals and O-rings. I had the flywheel ground too, that...
  14. E

    G1000 tranny and rear end check?

    What happens if it doesn't have the updated torque amplifier? Does that change the checkpoints? Thanks
  15. E

    G1000 tranny and rear end check?

    A buddy of mine just got a g1000 mm, and we"re trying to figure out how to check the tranny and rear end. Are they combined like the newer ones and run hy-tran or are they both separate and run 80-90? And where are they checked from? Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top