-
F
110 yaers ago today...
DeltaRed I got fat Fingers- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
110 yaers ago today...
DeitaRed where at in Western Colorado? Delta? I used to live in Grand Junction.- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
Farmall M
Nick Is there a Contact? Is the tractors for sale? Rockford is over 100,000 population. Thanks- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
Farmall M
Comstock Implement was on the West Side of Rockford. Just off Meridian Road on West State Street. Does this fellow still farm on the West Side of Rockford? Thanks- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
Farmall M
Was the angle iron holding the light on or just welded to the light tube next to the light on the right side? From what I remember the angle iron was along the light bar and stuck out in front of the light. I do not remember a back light, but it could have been added. Do you know of a contact...- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
Farmall M
Trying to track down an M. Was traded to Comstock Implement in Rockford Illinois in 1973. Only distinguishing feature that I can remember was there was a Angle Iron Bracket welded to the light bar on the right side. I know this is worst than a needle in a hay stack, but doesn't hurt to ask...- farmall706
- Thread
- Replies: 6
- Forum: Farmall, International & McCormick
-
F
Jerking Farmall 706
I had the same thing happen on my 706. If I touched the brakes it would take right back off. What fixed mine was to remove the MCV and rebuild it. Kit was about $80. I also had no pressure on a gage when I put a gage where the sensor is located at the back side of the MCV. It should read...- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
Cub Cadet 1512
Does anyone know of a place to get used parts for this lawn mower? I need a temp gage. The engine is a 3 cyl. Kabota.- farmall706
- Thread
- Replies: 2
- Forum: Garden Tractors
-
F
cub cadet 2135
It does have an electric clutch. I will take a volt meter with me tomorrow and check for voltage at the connection to the clutch? It has acted up a couple of times in the past , like you may need to pull the switch on and off to get it to work, but nothing tonight. Is there any rebuilding the...- farmall706
- Post #1
- Forum: Garden Tractors
-
F
cub cadet 2135
Tractor starts and runs fine, but when I pull the switch to engage mower nothing happens? With the engine off and key on, I pulled the switch and hear no click. Is there something else to check? Thanks- farmall706
- Thread
- Replies: 3
- Forum: Garden Tractors
-
F
Wagon
Any one have any information on a Dultmeir (D90) Wagon. I am looking for some advertising literature or something to help in restoring for parades? It says it was from Manning Iowa. Thanks- farmall706
- Thread
- Replies: 1
- Forum: Implement Alley
-
F
MCV
When re-assembling the MCV should there be any sealant used or just new gaskets? Does anyone have the torque values when re-installing the MCV? The Pump feels tights, not real loose to the feel, so I would say it is not worn badly? That does not mean a lot though, a little clearance could be...- farmall706
- Thread
- Replies: 0
- Forum: Farmall, International & McCormick
-
F
MCV Question
What is the best way to remove the MCV from the tractor? I have all the bolts out, except for the pump bolts. Is there a way to jack it off with bolts? It must be doweled, and it is tight currently. Any suggestions? Thanks- farmall706
- Thread
- Replies: 4
- Forum: Farmall, International & McCormick
-
F
MCV Question
What is the procedure for bleeding it thru the MCV? Thanks- farmall706
- Post #1
- Forum: Farmall, International & McCormick
-
F
MCV Question
What is the best way to remove the MCV on a 706? Should I drain the Oil first? If I remove the MCV without draining oil, how much oil will come out. Where is the proper drain plug? Thanks- farmall706
- Thread
- Replies: 3
- Forum: Farmall, International & McCormick
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy