(800) 853-2651
SHOP NOW

Recent content by Ferguson to-30

Yesterday's Tractor Forums
  1. F

    Ferguson 30 Help

    This message is a reply to an archived post by Tom h. on April 09, 2019 at 07:17:16. The original subject was "Re: Ferguson 30 Help". Good morning, I was wondering if u still have that spring? I damaged mine and am looking for another.
  2. F

    Rocker arm bushing

    Hello out there, I needed to remove my rocker arm on my to-30 and at first glance was a bit stumped on how to remove it. After searching for a while I modified an idea I saw and came up with this. It is a 3/4in bolt (8in long) and 2 nuts. All grade 8. I shaved the nuts down to the size of...
  3. F

    Lift arms

    I got the left hand side off with lots penetration oil and a 6lb hammer. Right side is giving a fit to remove.
  4. F

    Lift arms

    It is not bad bent but I wanted to change it since I will have it apart. It has not ran in 10 yrs and I wanted to clean the pump and casing out before I start it.
  5. F

    Lift arms

    I don?t have any heat to put on them just penetrating oil. My right side arm is bent and I was wanting to change it. Will have to find something. Thank you for your input.
  6. F

    Lift arms

    How am I supposed to remove these arms? I removed the 2ea bolts from each arm. Softly hit each with a hammer but no movement.
  7. F

    Clutch

    Thank you so much!!!! I did as you said and it works very nice. I left just a small amount of free play for the pedal and the bearing. Thank you again for the help. Mike
  8. F

    Clutch

    How far do I rotate the shaft? If I rotate the shaft will that move the bearing fingers off the stop? I will do as you have said tomorrow and see what happens. Thank you for the help. I will update what happens
  9. F

    Clutch

    Working on my TO-30 And I just got done with replacing the clutch and brake shaft bushings and was wondering about the clutch. I was reading in the manual for setting the pedal after removal and noticed that when I push the pedal it does not touch the fingers of the clutch. The pedal is very...
  10. F

    Clutch and brake bushings

    Sorry bushing not bearing. I just did not want to put everything back together and take it back apart for a spinning bushing. It is only rotating maybe a third of a revolution. Just dont have much experience with these so that's why I'm reaching out.
  11. F

    Clutch and brake bushings

    I used a small 3 point hone stone for brake pucks. Now the shaft slides on smooth and it returns under the spring pressure. I operated the clutch pedal numerous times and I can't see the bearing move. Do u think the bearing will start to spin with the engine running and under more of a...
  12. F

    Clutch and brake bushings

    I took the clutch shaft out and the left hand outter bushing will slide in and out of the case with small pressure. Do I need to order more bushings and see if I got a bad one or add some type of sealant adhear the bushing to the case. Nothing to strong but just to keep it from spinning?
  13. F

    Clutch and brake bushings

    On a TO-30 how loose should the clutch shaft be? I installed new bushings and put the shaft back in. It is a snug fit and the shaft moves but not freely. If I push the pedal down it does not come up on its own. Slightly pulling up it moves back to neutral. Should it spring back on it?s own...
  14. F

    Bushing

    I installed the new bushings and the clutch shaft. It is a nice snug fit with the new bushings. With that said are u supposed to ream the bushings down? When I push the clutch pedal down it does not return on its own. I can pull up slightly on the pedal and it will return but only by pulling...
  15. F

    Bushing

    Sounds good, thank you
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top