(800) 853-2651
SHOP NOW

Recent content by ford4610

Yesterday's Tractor Forums
  1. F

    NH 489 roll bearing removal.

    I did find the set screws; my fingers and eyesight must be getting bad! It looks exactly like Jim.me posted a pic of. Now the fun part, the set screw is not budging, so I'm soaking in with PB blaster, then I will try some heat just with my propane torch. Thank you for everyone's advice.
  2. F

    NH 489 roll bearing removal.

    Thank you.
  3. F

    NH 489 roll bearing removal.

    On the 2 489s I have I only see 1 hole, At first I thought maybe a drift pin was in there, but only found 1 hole and no set screw, I will look at it more tomorrow, thank you.
  4. F

    NH 489 roll bearing removal.

    No. I so far just tried to see if a set screw was in there, I will try that tomorrow.
  5. F

    NH 489 roll bearing removal.

    Can anyone give me some advice on how to get the lower right side roll bearing out on a 489 Haybine? The service manual isent much help, what I see is a lock collar on the end of the roll shaft to hold the bearing assembly in, there is a hole in the collar, but no set screw, which leads me to...
  6. F

    What tractors did you drive as a kids?

    Ford 4600 with Dunham Lehr loader.
  7. F

    Repair or service manuals.

    what if I need a torque spec? or how much fluid is needed? ect? I don't expect much input from a simpleton who farms with junk!
  8. F

    Repair or service manuals.

    Ford truck manuals for my 2000 F250 and my Ford tractor manuals, it doesn't say who published them.
  9. F

    DIY A/C Repair

    Id say do it your self, i replaced the condenser, and compressor on my 2000 F250, and recharged it myself, and it works fine now, the only thing I haven't replaced is the evaporator behind the glove box. I hope I do not have to because it looks like a big job.
  10. F

    Repair or service manuals.

    Can anyone explain why service manuals are not like a book with normal chapters, why do they have chapters, with sections and the same page numbers threw out the manual. Normally chapter one is fuel system, pages 1 threw 20, chapter 2 engine, pages 20 threw 60, like a normal book, but most...
  11. F

    Ford 4600 3 pt category change

    Somebody must have changed the lift arm or the end, the end on the right of your hitch doesn't even have the casting for the spring retainer. Id go to a tractor salvage yard and see if you can find the end or the whole arm, if you live near a salvage yard, or look online, maybe All states ag, ect.
  12. F

    Mower deck leaves winrow

    That is perfectly normal for a brush hog mower, I have a woods M5, and a 6foot Howse, both do the same thing, that's how they discharge the cut material.
  13. F

    Ford F-250 gas engines

    My buddy has a 2015 with a 6.2, only 40,000 on it, but he likes it so far, it is a 16 spark plug engine, and otherwise a little hard to work on. The way he drives I think he gets 10 mpg.
  14. F

    Bat wing mower

    Thank you for the pics and replies everyone, I agree, a 12" would be my suited to my tractor.
  15. F

    Bat wing mower

    Can anyone who runs a 15 foot batwing mower tell me how many horse power are needed to run one for mowing down hay. Thank you.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top