-
FFuddy Duddy replied to the thread Head condition.I'll take something better than money. I'll take plastic. LOL. They said $140 each. But that's with no problems. What ever it cost at...
-
FFuddy Duddy replied to the thread Head condition.I pulled that rear valve and seen the crack in the seat and I guess I quit looking. Then see what I seen the second look. Hope no the...
-
-
FFuddy Duddy replied to the thread Head condition.Hey Hobo. Haven’t talked to you in a long time. Hope you are doing well. You’re right. The seat is cracked. Looks like I’m going to...
-
FFuddy Duddy replied to the thread Head condition.I went ahead and popped the valves out. That white valve has a couple little spots that look like it’s starting to go bad. The seat has...
-
-
FFuddy Duddy replied to the thread Head condition.That's water. Or more correctly 'sweat'. #3 does have a little pitting on the piston. But not too bad. That's where the gasket was leaking.
-
FFuddy Duddy replied to the thread Head condition.I thought that's what it was. Thing was, I was only seeing one. I got my magnet and swept around and found the other three. I've got the...
-
FFuddy Duddy replied to the thread Head condition.Level it up and fill it over the valves in a way I can tell which valve has the gas coming though if any is what you are saying?
-
FFuddy Duddy replied to the thread Head condition.I had the head upside down cleaning it up and seen this on the ground. I have no idea where it came from. Looks important. What is it?
-
-
FPulled the head off my '58 Ford 861 to replace the head gasket. It was running fine. Just seeping a little coolant. Been doing so for...
-
-
FI’m not a mechanic by any means. But I have rebuilt my share of engines. Run across this on a ‘56 Ford 172 industrial engine. Never seen...
-
-
FFuddy Duddy replied to the thread Finding a rubber grommets?.Looks like they sell it here for 60 cents. They call it an ' Oil Inlet Tube Seal ' I had seen it before. But that didn't sound right...
-
FFuddy Duddy replied to the thread Finding a rubber grommets?.That looks like it. They think highly of them. I need two. But they only have one. But that’s OK. Found one using that part number at a...
-
-
FFuddy Duddy replied to the thread Ford Industrial Engine.Thanks for the help. Now I can get somewhere with it.
-
FThis rubber grommets is on a 172 engine. Runs from the block up to the head to oil the stuff up there. Haven’t been able to find one...
-
-
FTrying to figure out what this engine is so I can get parts for it. I was told it came off of a combine. I just found the tag on it...
-
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy