(800) 853-2651
SHOP NOW

Recent content by Gator123

Yesterday's Tractor Forums
  1. G

    1466 transmission

    Hello everyone. I have a question about the transmission gears in my 1975 international 1466. I have everything apart so i can replace the ta. My question is some of the gears are worn a little and some of the teeth are chipped around the edges. Not very much and not all the teeth on the...
  2. G

    International 1466 spool valve

    Hello, i have an international 1466 that i am re-sealing the spool valve that is under the seat with new o-rings. My question is when i removed the detent actuating pin that has the small o-ring on one end, it came out too fast for me to pay attention as to how it goes back in. Does the o-ring...
  3. G

    International 1466

    I forgot to mention that even when the tractor quits pulling the clutch, power steering, and brakes all still work. Thanks.
  4. G

    International 1466

    Hey guys. I just purchased an international 1466 to restore. I have always wanted one on the larger IH tractors and this one runs great but is having some trouble pulling itself. I have already ordered all the manuals but wanted to ask some of the experts. From what i can see the clutch looks...
  5. G

    John deere 60 pto clutch

    Good idea tim. I may do that on mine before i paint. Perfect timing. Thanks again
  6. G

    John deere 60 pto clutch

    Thanks tim. I have already changed the pto shaft seals and bushing. It doesnt look like transmission geal oil is leaking into the pto housing. I was just wondering if it was normal for pressure to be built up in the pto housing. I may have over filled it with new oil but i dont think that would...
  7. G

    John deere 60 pto clutch

    I have a john deere 60 that i am prepping for paint and noticed oil seeping out from around the large fill plug in the pto clutch housing. As i removed the fill plug there was a little pressure built up. Is there a vent that i am missing? It hasn't been ran that much after i rebuilt the pto...
  8. G

    John deere 60

    Got the generator and wiring figured out. I had it wired up correctly but found the contacts stuck shut in the voltage regulator. The generator had just been rebuilt and the regulator is brand new so i didn't think much about something being wrong with them.
  9. G

    John deere 60

    Hello to all. Finally got my john deere 60 running today. Sounds pretty good. Just have a few questions. The first is about the wiring on the generator. My 60 is a late 1953 model serial number 6028909. The john deere wiring harness kit that i got has two wires, a white and a black one. I have...
  10. G

    1954 john deere 60 wiring diagram

    Thanks Dan!
  11. G

    1954 john deere 60 wiring diagram

    Does anyone have a detailed wiring diagram for a 1954 model 60. Serial number 6028909. Thanks.
  12. G

    John deere 60 clutch

    The compression is very good. New pistons, rings, machine work ln head and valves, etc. I just left the spark plugs loose while i was barring the engine over by hand to time it. Good thinking though. Thanks.
  13. G

    John deere 60 clutch

    I do have quite a bit of slop in the linkage from the clutch lever to the fork lever. Didn't think about that but i can see where all that slop might keep the clutch from snapping in hard. Thanks for the reply. I had planned on trying to weld up and re-drill some of the worn out holes in the...
  14. G

    John deere 60 clutch

    I have a 1953 john deere 60 that i am restoring and had some concern's about the engine clutch. Hopefully it is nothing much to worry about. I cannot get the clutch to snap in and out like everyone talks about. As i engage the clutch handle i can feel it cam over and it does take some effort to...
  15. G

    Ford 3000 hydraulic line

    Hello to all. I have a 1975 ford 3000 gasoline tractor that has a hydraulic leak from the smaller steel line that goes into the hydraulic pump. I have removed the line and ordered the new nut kit which also includes the rubber seal, two washers that are for the rubber seal and what looks to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top