(800) 853-2651
SHOP NOW

Recent content by Gene Beckham

Yesterday's Tractor Forums
  1. R

    1070 case 3 point arms

    I have 1070 that the 3 point arms are at lowest point and just bounce a little but, will not raise. I was told the A59600 valve was the problem. Received some info from online to check draft cable and spring on valve. Both are okay and valve spool looks clean like it had been moving. Any advice...
  2. O

    730 power steering fluid

    Drained the power steering on my 730 today, oil was dark and thicker than what I'm used to. Book says John Deere power steering fluid, what grade oil is this and what would be a good equivalent? Sure made a mess, doesn't look like a clean way to do that though. John
  3. C

    6410 remote valve flow.

    I am looking into putting a selector valve on my loader to split the flow for a grapple. I don't want to choke my system and slow my cycle speed down. I am sure the remote flow is considerable less than pump flow. Any one know for sure the flow specs on a factory installed deere loader valve.
  4. B

    Piston Pump for NAA/Jubilee

    I had a 54 NAA about four years ago and sold it when my daughter went to college. (9N before that) She is graduating this spring and I wanted another tractor so I recently bought a 53. It needs work. (Maybe more work than I thought.) It has been neglected. I have had it a week and this is...
  5. A

    4430

    still working on getting it started fixed leak in fuel line jd wanted twenty eight dollars for a ten inch line cut ends off and put rubber fuel line three dollars cant see it any way under fuel tank installed a new primer pump on injection pump it would leak when you pumped it still will not...
  6. J

    super m head gasket

    i overhauled my super m during the summer and i also put a new block in it, the block was checked and plained, the head was gone through and plained, everything was checked and gone through. just for the hell of it i loosened the drain plug the other day and about 2 or 3 bottle caps full of...
  7. G

    Screaming Farmall Super C

    Cliff S I run old 13-38 45 degree top cuts but at the low rpm I should have been ok but it just wasn't my day.I'm to heavy to run 3250 b as i have front wheel weights plus my big butt gets me too heavy. I went to princeton to pull with my friend Gene Sellers as he is not pulling as much as...
  8. G

    9 bolt hub U Bolts??

    I've purchased u bolts from this place in Lebanon,mo .They will make them any size & they were not that expensive. 417-532-3167 & they came UPS Good Luck Wildman from MO
  9. G

    Tractor Salvage Yards?

    hilltop salvage is at Lamar,mo.
  10. G

    Tractor Salvage Yards?

    yes JP salvage at Fredericktown,mo 573-783-7055 IH only letter tractors.Hilltop salvage 417-398-2816 lots of equip.Gerald runs it & a nice fellowWildman from MO
  11. G

    wc or wd?

    wc can get into lighter classes
  12. G

    little#8 manuals

    I guess your talking about alittle genuis ihc plow? someone last week tipped me off to the web site of www.external_link. Went there found lot of old manuals. phone 503-684-2024 hope this helps...Wildman from MO
  13. G

    disc brakes on a farmall c

    I have a c farmall rear end housing that I would like to put disc brakes.I use this tractor for pulling & read somewhere the c is 70 lbs. lighter than the super c.some of that weight may be in the torque tube.I was hoping some of you farmall whizards would know if it can be done without alot of...
  14. G

    breaking tire bead

    this may sound silly but old man at a tire repair shop told me to pour gasoline around the bead wait a couple of minutes then hit it with your tire wedge.The gas eat at the rust of 40 plus years of calcuim. Three or four licks should break it down. Sounds dumb but it works every time for me...
  15. G

    Phone number for Al Mahnke

    618-758-2017 the last time i called him.wildman from mo
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top