(800) 853-2651
SHOP NOW

Recent content by greebas

Yesterday's Tractor Forums
  1. G

    Farmall 504

    Considering buying a Farmall 504. Any issues with that model I should be concerned about? Also, this tractor currently has a tricycle front and I'd like to swap it out with a wide front, can this be done? thanks
  2. G

    MF 165

    I'm trying to determine the minimum width tiller needed to cover tire tracks, thanks.
  3. G

    MF 165

    Need to know the width between rear tires on MF 165 ( outside edge of tire) Thanks
  4. G

    MF disc

    Wanting to know if a 6 1/2 ft. disc is wide enough for a MF 165 ( to cover tire tracks) Thanks
  5. G

    MF 165 3 bottom plow.

    Thanks Your post with first hand experience settles it for me.
  6. G

    MF 165 3 bottom plow.

    Just wondering how well a MF 165 will pull a 3 bottom plow( 14"s)in my semi- clay soil. Thanks
  7. G

    MF 150/165 Difference

    Kind of what I was thinking
  8. G

    MF 150/165 Difference

    Just a question out of curiosity: I noticed on tractor data sight that there was very little weight difference between an MF 150 and 165. Are these basically the same frame sized tractors apart from a bigger engine and tires on the 165? Thanks
  9. G

    Perkins 3.3/3.5

    Would like to know what determined which Perkins diesel engine ( 203/212 ) was used in the 165. Was the 212 an upgrade in later years or just an option? Any significant difference in reliability? Thanks
  10. G

    Chisel plow for Massey 165

    Thanks Eric, that settles it for me.
  11. G

    Chisel plow for Massey 165

    I've always heard you need 10 hp per shank. Have you found this not to be true?
  12. G

    Chisel plow for Massey 165

    Does this cultivator rip the soil deep enough to plant a garden? Thanks for the picture and info.
  13. G

    Chisel plow for Massey 165

    I"m wondering if anyone has used a chisel plow(not a cultivator) with a Massey Ferguson 165. I would like to use a 5 shank to plow up my 2 acre garden in spring and fall. Obviously the ground is already broken up, but I just want to be sure I"ll have enough horsepower before I buy the chisel...
  14. G

    MF 150

    I"m considering purchasing a MF 150 with the gas engine. I know the Perkins diesels are very good engines and am wondering if the gas Continental has any reliability issues. Thanks
  15. G

    MF # 25 disc.

    Thanks chuck.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top