(800) 853-2651
SHOP NOW

Recent content by Guigui

Yesterday's Tractor Forums
  1. G

    Dumb question about light switch

    So after re-reading your description, on the label, S for Side, D for Dipped, M for Main and P for Plough, it makes sense now
  2. G

    Dumb question about light switch

    I just went through the owner manual again, it shows how to adjust the valve lash but not how to operate the light switch. times have changed, I guess on new tractors it shows you how to turn the steering wheel and nothing on the valves... That being said, I found a picture of the original...
  3. G

    Dumb question about light switch

    Hi, I have this mostly new to me b275 and the wiring is kind of a mess. It is missing ths tag on the light switch also. I wonder what all the positions do on the switch. I looked the owner manual and searched a bit on Internet but did not find anything
  4. G

    Help identify power steering

    Ok, just an update, it seems that the "valve" part, that is load sensing is sloppy but when properly lined up it is working. It is just not well installed as of now. But I don't know if you can see it on the pictures, the rod is severly scored, that is why it is leaking so bad. Now I need to...
  5. G

    Help identify power steering

  6. G

    Help identify power steering

  7. G

    Help identify power steering

    Hi, I got this old B275 that had a power steering ram "fitted" by previous owner. Unit is done I think, does not really help the steering and it is leaking like nothing. I want to find out if I can find parts to rebuild it or replace it. I have been told that it is a unit from a fork lift...
  8. G

    differences between b275 and 414

    Thank you, do you know if the back half parts (transmission, differential, axles etc) are interchangeable between both?
  9. G

    differences between b275 and 414

    Hi, I have an '62 b275. I might have the possibility to get a 414 for the parts, are there enough common parts between both to make it worth it?
  10. G

    B275 Bull gear

    As far as I know it has been that way for years and did not get any worse. I will groove the cracks, drill on each end and weld it. Just to make sure it is not leaking by any pinhole, I will JB Weld it
  11. G

    B275 Bull gear

    You would not happen to know the tollerances for those?
  12. G

    B275 Bull gear

    Yes after thinking about it I will weld, I have cast iron welding rod. I just dont trust my welding skills to be confident that it will not leak, so I might jbweld over my weld. Like grins, weld and JB weld I have inspected bearings and they look good, I will replace both bull pinion bearings...
  13. G

    B275 Bull gear

    It r It really looks fine to my eye
  14. G

    B275 Bull gear

    Well things explains themselve. Remember that I took it appart because of a badly leaking seal. I found the cause of it all. It seems that the housing is cracked. You think cleaning and JB weld would be enough? This post was edited by Guigui on 01/04/2023 at 04:24 pm.
  15. G

    B275 Bull gear

    I honnestly do not beleive I need a bull pinion, it looks in pretty good shape. Il will inspect it more and disasemble the rear end until I find what happens. The debris make me beleive that at some point a bearing cage broke and it got in the gears
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top