(800) 853-2651
SHOP NOW

Recent content by H D

Yesterday's Tractor Forums
  1. A

    Engine Swap (5420 into a 5203)

    I"m considering a JD 5203 (3 cyl, 56 hp) with a 5420 engine (4 cyl, 65 hp) in it. The original engine was replaced because of a cracked block. I haven"t gone to look at the tractor since I"m hesitant about this engine swap. It was done by a father and son team that repair and resell farm...
  2. A

    4600 throttle shaft leaks

    My older farmer friend asked me today to help with a diesel leak on his Ford 4600. The throttle shaft is leaking a slow steady drip. Throttle shaft seems pretty tight. Can the linkage be pulled off and the seal replaced, or does the pump need to come off and be sent out? Thanks for your...
  3. C

    Adding coulters to Dearborn 10-156?

    Hello! I have a Dearborn 10-156 plow that I bought without coulters (see pic). I"d like to add some. I"m not doing a restoration, so any coulter setup will do. But someone told me that adding coulters to this plow will be difficult since the coulter stem is 1 1/8 which is difficult to find...
  4. A

    What has happened?

    What has happened? I now have all of my transmission oil in my hydraulic case and the tractor barely moves and my pto has no power. The tractor is a 1959 select-o-speed
  5. S

    Paint don't pull but a little IH white looks nice!

    Looks good . I want to do the same type of job on my M. I was thinking of swaping the colors around just to be different. How's the pulling going with the high speed hay rake? Untitled URL Link
  6. 8

    nuffield 30-35 hp

    Does a Nuffield 30-35 hp tractor have hydraulics and a pto in the back that can run a New Holland hay bine and a New Holland 68 baler?
  7. R

    Ditch Witch V30 parts needed

    We"re needing rear differential parts for a Model V30, any ideas would be very helpful, call 920 295 3278 or email [email protected]. Thanks, Dale
  8. M

    30 inch rims??

    I am looking for a set of 30 inch diameter rims in the lower peninsula Michigan area. 517 719 7443
  9. L

    another typical day at work

    jackhammer, heave the chunks on the truck,get ready for concrete, same proceedure,different spot
  10. T

    McCormick Deering 50T baler

    Anyone have a hood.
  11. C

    BGAP pull

    pull for sat April 30 cancelled " RESCHEDULED " sat May 7 1:00 3,5,8,12 mph questions call 859-707-8040
  12. H

    Lift piston on 9N

    I am replacing the lift piston on my 9N with the NAA530B piston,rubber o-ring and washer. My question is in what order are the o-ring and washer installed and from which end? Hope this makes sence. First time doing this. Thanks Tom
  13. H

    9N hydraulics

    Thanks for all your great help!
  14. H

    9N hydraulics

    When I push in the clutch the blade is on the ground in about 30 seconds.
  15. H

    9N hydraulics

    Was pulling some large bushes out with my 9n with blade and a chain to the bush. I had the blade slightly raised while pulling. After I pulled bush out the blade drops as soon as I push in clutch, and when blade is up and I climb on top of blade it slowly lowers. My question is what did I do to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top