What has happened?

Anonymous-0

Well-known Member
What has happened? I now have all of my transmission oil in my hydraulic case and the tractor barely moves and my pto has no power. The tractor is a 1959 select-o-speed
 
Believe either an 871 gas or 881 Diesel? Either way, if ALL the oil is in the diff, some seal / gasket let go. Split the tractor & fix it!
If there is still some oil in the trans, then the front pump behind the flywheel & slip clutch has lost efficiency. (now get to split the tractor here as well) If pump can't pressurize oil to run the valve system will not energize planetary slave pistons, planetary brakes, or the last in sequence, the independent PTO valve.
Likely in either case it did NOT happen all at once but over time.
My suggestion is NOT to even start the tractor till you can get the trans fluid level up to correct level. Then find out where it is going before you try to move the tractor.
There is a VERY remote chance that the SOS disconnect may have moved but this means a lock out bolt was removed or backed out, and it collar moved by itself off the diff input shaft. VERY unlikely!
If you can get the oil level up to level and you can observe some pressure at the valves body by GENTLY moving the speed change quadrant you might be able to move tractor to shop location for permanent fix.
Gotta love the select o speeds! If you give up, let me know when you want to sell it!
Glenn
 
(quoted from post at 20:47:16 07/31/11) What has happened? I now have all of my transmission oil in my hydraulic case and the tractor barely moves and my pto has no power. The tractor is a 1959 select-o-speed

Good Evening 555,

Based on your original post, I believe shaun likely has the accurate diagnosis. If you don't have a manual, now would be a good time to get one.

Your model number will be 871 or 881 depending on whether you have the 540 PTO only (871) or the 540/1000 PTO (881). The common seal failure between sumps would move some oil, but not ALL oil. The fact it all has gotten transferred means it's leaking from the pressurized portion of the system. It's possible for the control valve to leak between the two halves, BUT, that would drop oil in the original sump and while you would have loss of function, you wouldn't have the tranfer of oil you are seeing. Most likely, as shaun has diagnosed, the lubrication sending unit has come out or failed and is allowing the transmission oil to flow into the hydraulic sump.

The fact it was still trying to move indicates the "traction" coupling (between the transmission and rear end) is still engaged. I would disengage the traction coupling and pull the tractor to a repair location.

Now the possibility of good news, IF it is the lubrication sending unit that has failed or come out, a split may not be neccessary. First, drain your hydraulic resevoir to a normal level, collecting the oil. Assuming it is reasonably clean, refill the transmission reservoir. Then (after drainaing the hydraulic fluid below the bottom of the inspection plate) REMOVE the inspection plate that includes the traction disconnect and hydraulic dipstick. Disconnect the traction coupling and look through the inspection port to the front of the tractor. You should be able to just see the lubrication sending unit. NOW, start your tractor and look/listen for fluid coming from this area into your hydraulic sump. If it has broken or come out for some reason you should be able to see/hear the incoming "leak" and may find ithe sending unit in the bottom of the sump by feeling around (don't remember how easy that is, it has been a few years). If you find that is the problem and can get the threaded hole "open or clear" to accept a new sending unit, it may be a very reasonable repair. I replaced my lubrication sending unit about 5 yrs ago, through the inpsection port. Not easy or fun, but doable, PLUS, if you do that you get the added benefit of a functioning lubrication warning light. Please let us know what you find and we will provide additional info. Others here know oodles more on these tractors than I do, but I believe shaun has is right.

Chris
 
Thank you everyone especially Chris. I do have a manual and a parts book for this tractor. The stamping on the side of the tractor transmission is 312259 CWC J169. To my knowledge it is a 1959 801 gas select-o-speed. I have had the side cover off that the traction disconnect last week when I was unable to get the tractor disengaged. I did notice a wire that was hooked to the plate and I cut it off. Was that the sending unit? This all started a couple of weeks ago while mowing on a hill. The tractor stopped pulling and pto stopped. I was unable to get the tractor disengaged to move it until I got on here and someone suggested to jack one wheel up and I would be able to disconnect and it worked. When I got on flat ground again the tractor started moving on its own. I figured then the oil maybe low and the screen needed cleaned and I did clean the screen and filled with new from New Holland dealer G 134 oil. Everything seemed to work for a while until again on slightly sloped ground it was starting not to move and the pto stopped turning that is when I noticed the overflow in the hydraulic tank and the transmission being low on oil. Please accept my apologies for having a difficult time explaining my problems through typing I just don’t know all the tech terms. I have owned this tractor for 18 years of its 52 years and have not abused it. I really like the select-o-speed for mowing and tilling. I hope I can get this problem fixed without completing going broke. Thank you once again everyone and including this site for all the information.
Roger
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top