(800) 853-2651
SHOP NOW

Recent content by HeyObie

Yesterday's Tractor Forums
  1. H

    Question about valve clearance 8N front mount

    When I could not figure out the problem and my guess was carb, I bought one from this site. After a year or so passed (been limping along for 3 years with this problem), I read that some of these carbs can cause problems. So I bought another one to see if I got lucky. So I bought another one...
  2. H

    Question about valve clearance 8N front mount

    Jim, Gotta go get dinner but will respond to your items. As far as air leaking into the system, this is what I did last year. I pulled the manifold. I have a large table belt sander. I put the manifold on there and ground it done until everything was clean as a whistle. I took a single...
  3. H

    Question about valve clearance 8N front mount

    Ignition timing can effect power, and or the mechanical advance weights, also cylinders 2 and 3 plug wires being switched. Have you checked these items? Is the engine acting like it is missing or running smoothly? Have you checked the governor to see if it is working properly? I have moved...
  4. H

    Question about valve clearance 8N front mount

    I have the intake/exhaust manifold off because i was going to pull the head so there is no intake restriction when i did the compression test. I am at such a loss. These tractors are so forgiving. I am missing something obvious. 3 carbs, 2 fuel filter cutoffs, 6 volt to 12 volt to...
  5. H

    Question about valve clearance 8N front mount

    I have the intake/exhaust manifold off because i was going to pull the head so there is no intake restriction when i did the compression test. I am at such a loss. These tractors are so forgiving. I am missing something obvious. 3 carbs, 2 fuel filter cutoffs, 6 volt to 12 volt to...
  6. H

    Question about valve clearance 8N front mount

    I am sorry. My decimal point is off. You were correct. .018 Plugs NGK B4L
  7. H

    Question about valve clearance 8N front mount

    I agree Cylinder 1 is closest to the radiator. I am showing from left to right as if you are looking at the tractor. The gap is off .02 not .002... is that significant? I think the compression takes a second to build up because it is filling up my gauge and hose.
  8. H

    Question about valve clearance 8N front mount

    Been having problems with my 8N for a couple years. Used to run great. Does not have enough power to run my 5" mower. It is not electrical. It had the problem when it was 6 volt. Switched to 12V because I could never get the regulator and generator working. New wiring. Fried points and...
  9. H

    Can't get front mount 8N running right.

    I will also run propane test
  10. H

    Can't get front mount 8N running right.

    I pulled the manifold off today I basically milled it on my 2 foot by 6 inch belt sander. Cleaned the block with a razor blade. Gaskets were tired And a little suspect. replaced both manifold gaskets and the gasket at the carb I seal both sides of the gasket with a high temp silicone sealer...
  11. H

    Can't get front mount 8N running right.

    Front mount 8N Just can't get my 8N running right. It does no have enough power to cut the grass on a flat surface. I can get more power if I pull the choke out about an inch but it still is not right. When I start it up, it is stronger and gets weaker as it warms up. I have been messing...
  12. H

    8N front mount resistor help for electrically challenged

    OK. Thank you. Why do the 12v conversion kits send a second resistor? Is that to protect the 6 volt coil?
  13. H

    8N front mount resistor help for electrically challenged

    Would you know how many watts the resistor should be?
  14. H

    8N front mount resistor help for electrically challenged

    I am struggling getting my front mount 8N running right. I switched to a 12 volt system about a year ago mainly because I could never get the 6 volt charging system running( I tested the generator, polarized and switched regulators). So the tractor kept dying and I was constantly charging and...
  15. H

    Trouble bench testing points and coil 8N Front mount

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top