(800) 853-2651
SHOP NOW

Recent content by hilljred

Yesterday's Tractor Forums
  1. H

    kubota

    got a kubota v800 from a golf course mower. iis a 4 cylinder diesel engine. it runs very good. i would like to know the hp of this engine, thanks
  2. H

    kubota

    got a very good running v800 kubota diesel engine 4 cylinder. would like to know the hp of this engine
  3. H

    Onan Engine

    I just bought a Craftsman riding mower with a 20 hp Onan engine with electronic ignition. It has no spark. I would like to know how to check out the coil and the pickup for the ignition. I believe it to be a good engine. It has 110 psi on each cylinder compression. The sears model no. is...
  4. H

    carb problems

    i have this ariens zero turn that has a 17hp - ohv intek b&s engine thar has me completey baffeled. it will run with choke about 2/3 closed. i have disamabled the carb many times and cleaned it cant find any problems other than the plastic float might need to be adjusted. i can mist a little...
  5. H

    d600 kubota diesel engine

    got a d600 kubota that runs and smokes quite a lot. will pull the injectors sunday need to know the pop of pressure. got a pressure tester. any other words of wisdom welcome. thanks
  6. H

    karcher power warsher

    bought a karacher hot warer power warsher would like to know what chemicle to use on the feed for better results. it is a 1989 model it seems to work like i think it should. havent much experince with a hot water power warsher. thanks
  7. H

    zero turn mowers

    bought a woodsmow'n machine 1850. 18 hp brigs & stratton 50 inch cut . the man said he thought it was made by grashopper. went and looked a friends grashopper it is a lot latter model with a kubota diesel engine, many of the components are the same. my mower must be atleast 20 years old. can any...
  8. H

    tread plate tool box

    i picked up a alunium tread plate tool box for the truck it has a few skuf marks on the front. what could be used to remove the skuff marks ? dont know what they are from may be from a spare tire rubbing against the metal. thanks
  9. H

    aluminum concrete forms

    bought some aluminum concrete forms that havent ben taken care of to well there is quite a bit of concrete sticking to the forms.what will take the concret off that wont heart the aluminum ? thanks
  10. H

    lawn mower starters

    the ladrs lawn tractor wont start turns over slowly and eraticly. took it off several times before i found out that the magnets was not glued in to the housing. what kind of glue or epoxy would you fellows recomend? thanks
  11. H

    oil filters

    bought a craftsman gt 18hp twin rider to put the 42"snowblower on the motor is a 18hp twin kohler magnum got it running now need to change the oil and filter what weight oil shud i use. do i have to use the kohler oil filter or is there other filters that might be less expensive? what size...
  12. H

    point plug gap

    BIL ask if me what the point & plug gap was for his mewly purchased 41 b john deere was. so i said i would try and find out. thanks
  13. H

    front mounted snow blower

    i have a sears front mounted snow blower. the id plate is mostly missing all that is left is G15 and directly below is 636. it is a 42" model. it is older model looks like it fits a sears model that has a vertical shaft engine and has arms that atach to sides of tractor. thinking i could find a...
  14. H

    recoil start rope

    i have a 6.5tecumseh engine that the recoil rope btoke. what is the easiest way to get it apart? it looks like a large role pin in center of recoil and no screws at all. put alittle presure what looked like the roal pin and the hole recoil began to deflect so stoped that and thought l had better...
  15. H

    2BT 3PT 14 DEARBORN PLOW

    GOT A CHANCE TO BY ONE 2 BOTTOM 14 INCH DEARBORN 3 POINT PLOW IN JUST SO SO CONDITION. WHAT DOES IT WEIGHT. .25 CENTS A POUND IT WILL COST ME. WOULD LIKE TO KNOW THE WEIGHT BEFORE I SAY YES. THANKS
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top