(800) 853-2651
SHOP NOW

Recent content by hoipigeons

Yesterday's Tractor Forums
  1. H

    completely and totally confused

    Coil says no resistor needed
  2. H

    completely and totally confused

    What would cause that, and how can I cure it. The coils have all been listed as no resistor needed. Would electronic ignition cure the problem, or would it burn up also?
  3. H

    completely and totally confused

    They have both burned up coils, all were no ballast needed coils.
  4. H

    completely and totally confused

    OK, let me start over. My "A" and my "B" are both on 12 volt systems. I converted the "B" several years ago. My point is this---I have one distributor that works like a top! No problems. It works on either 12 volt tractor. I had a distributor that had been working on the "B", but the coil...
  5. H

    completely and totally confused

    I've already burned up 3 coils!
  6. H

    completely and totally confused

    So Sorry. Forgot to mention the B is also 12 volt.
  7. H

    completely and totally confused

    I started my old B this spring, and it ran good for about 15 minutes, then died. Coil was SUPER hot! Bought a new coil. Same thing. Put in new points, no go. New condenser, same. Swapped it out with the one on my A. B runs great, A won't start now. Sent distributor in to be checked over and...
  8. H

    John Deere G brakes

    Don't know for sure, but it sounds like somebody went to fix the brakes, and used what they had sitting around, or were able to purchase cheap.
  9. H

    carburetor question

    Thanks for your help!
  10. H

    carburetor question

    Thanks Mike!
  11. H

    carburetor question

    I meant the bowl baffles on the main body of the 51 carb from a '51 G.
  12. H

    carburetor question

    Does anybody ever replace the throttle shaft plugs in a 51 carb? My kit doesn't have them, and looking around, they seldom do.
  13. H

    governor problem

    Deere Sorry, I spaced off looking at this for help.
  14. H

    G governor

    Need some suggestions on how to fix my 1950 "G" governor problem. Seems it either idles, or goes full bore. How do I correct this to get a nice normal progression of rpms?
  15. H

    governor problem

    My 1950 G doesn't seem to have a between speed. It either idles or is wide open. How do I fix this? There has to be an adjustment to the governor somewhere that I'm missing.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top